Pelco installation manual Setting Up the DX9200HDDI, Installing the Hard Drives

Page 15

Setting Up the DX9200HDDI

This section describes how to install the hard drives in the DX9200HDDI and configure the DX9200HDDI to operate with the DX8100 DVR. After the DX9200HDDI is configured, the next step is to connect the DX9200HDDI to the DX8100 DVR, and finally, configure the DX8100 DVR’s Basic Input Output System (BIOS) to recognize the DX9200HDDI. For information about installing additional drives, refer to the documentation that accompanies the DX9200HDDI.

INSTALLING THE HARD DRIVES

To install the hard drives in the DX9200HDDI:

1.Do the following:

a.Remove the hard drive tray by lowering the panel that houses the LCD display.

b.Push down on the release latch to remove the tray from the DX9200HDDI.

2.To ready the hard drive for installation, do the following:

a.Remove the hard drives from any protective packaging.

b.Set the jumper for each hard drive to Master. For information about setting the jumper, refer to the hard drive’s manufacturer’s instructions.

c.Insert the power plug into the power connection on the hard drive.

d.Connect the external IDE cable to the connector on the hard drive.

Figure 11. DX9200HDDI Hard Drive Tray

3.Place the hard drive into the tray, be sure not to pinch or damage the external IDE cable. Secure the hard drive with four Phillips screws. (Size 5 mm, #32 flat head).

4.Slide the tray into an empty slot until it clicks. Push the lever down until it locks in place. Repeat these steps for any remaining hard drives.

C2635M (1/07)

15

Image 15
Contents DX8100-ISCI Scsi Page Contents List of Illustrations C2635M 1/07 List of Tables Introduction Parts ListTools Needed Other DX8100 Optional AccessoriesGetting Ready Installing the DX8100-ISCI Scsi CardOpening the DX8100 Chassis Preparing the DX8100 for Scsi Card InstallationCPU Understanding the DX8100 Component LayoutMoving the Main Capture Card to Slot Moving Main Capture Card Installing the DX8100 Scsi CardReassembling the Unit Installing the Hard Drives Setting Up the DX9200HDDICtrl Configuring the DX9200HDDIConfiguring a Single RAID Level 5 Array Specifying the Number of Hard Drives in the Array Single RAID Level 5 Array Initialization Status Description Configuring a Single RAID Level 5 Array with HOT Spare C2635M 1/07 Configuring TWO RAID Level 5 Arrays C2635M 1/07 C2635M 1/07 C2635M 1/07 Configuring TWO RAID Level 5 Arrays with HOT Spare C2635M 1/07 C2635M 1/07 C2635M 1/07 Deleting ONE Array Deleting ArraysC2635M 1/07 Deleting TWO Arrays C2635M 1/07 DX8100 Connecting the DX8100 to the DX9200HDDIConfiguration Instructions for Storage Arrays UP to 2.0 TB Configuring the DX8100 to Access the DX9200HDDIMy Computer Quick Menu Computer Management window opens Select Disk to Write Signature Dialog Box C2635M 1/07 Create Partition Wizard Specify Partition Size Dialog Box Click Next. The Assign Drive Letter or Path dialog box opens Click Finish. The new drive appears in the device list Opening Drive Options Menu Initializing Drive Allocation My Computer Quick Menu Configuration Instructions for Storage Arrays Above 2.0 TBWrite Signature and Upgrade Disk Wizard Select Disks to Upgrade Wizard Dialog Box Unallocated Space Shortcut Menu Specify Partition Size Dialog Box Click Next. The Assign Drive Letter or Path dialog box opens Click Finish. The new drive appears in the device list C2635M 1/07 Initializing Drive Allocation Product Warranty and Return Information ISO9001
Related manuals
Manual 20 pages 10.68 Kb