Pelco C2602M-a manual Camera Settings, To configure cameras

Page 56

CAMERA SETTINGS

Use the Camera tab to configure general information for each camera. You can create a title, adjust the color quality, turn on covert recording, and enable and configure PTZ controls for each camera. You can also set the baud rate that the DX4000 uses for all cameras.

Figure 70. Configuring Camera Settings From the Remote Agent

To configure cameras

1. From the remote agent application main screen, click the Setup button

if the Settings screen is not open. The Settings screen

appears and the Remote Agent tab is displayed.

 

2.Open the DVR System tab, and then click the Camera tab.

3.Enter a title for each camera. This title appears on the screen if you have enabled it on the display settings.

4.Under the Color settings, select the brightness, contrast, color, and tint settings for each camera.

Brightness: Adjust this setting to display black picture content as true black on your monitor.

Contrast: Adjust this setting to distinguish between the darkest and lightest picture content on your monitor.

Color: Adjust this setting to increase or decrease quality of the color picture content that is displayed on your monitor.

Tint: Adjust this setting to increase or decrease the saturation of color for picture content that is displayed on your monitor.

5.Under the Covert/PTZ settings, configure the following information for each camera:

Covert: Set this to On or Off. If your turn on covert recording, the DX400 will record video from the camera, but it will not display live video from the camera.

Address: Enter the PTZ address for the camera. This number must match the pin number that was selected on the camera. Change this number to match the number in use by the camera.

PTZ Protocol: Select the protocol. The DX4000 supports a wide range of PTZ protocols. Refer to the manufacturer’s documentation provided with your camera to select the correct protocol.

6.Select the baud rate for the RS495 port. Choices range from 2400 Kbps to 19200 Kbps.

7.Click the Apply button to save the changes and continue to other settings. If you are finished updating settings, click the OK button to close the screen.

56

C2602M-A (6/06)

Image 56
Contents DX4000 Digital Video Recorder Contents C2602M-A 6/06 List of Illustrations List of Tables Description Features ModelsConnecting Devices to the DX4000 Overview of the SystemDX4000 Controls Controls on the Front Panel of the DX4000Video Control Buttons on the Front Panel of the DX4000 Control Buttons on the Front PanelOperating the DX4000 from the Remote Control To start the DX4000 Before You BeginStarting and Stopping the DX4000 Table A. User Accounts and Access Levels All manager and operator accessChoosing a User Account To stop the DX4000Main Window Overview Changing the Information Displayed on the Monitor Changing the Display ModeTo change the screen sequencing mode Adjusting Menu Settings Display MenuRecord Menu Camera Menu Audio MenuAlarm Menu Use the Alarm menu to set up alarms and relays for camerasSystem Menu System MenuBackup Menu Back UP MenuChanging Passwords Password MenuResetting Passwords To reset the passwordsFactory Default Settings Factory Default Reset Warning MessageScreen View Selection Screen Rotation ModeChanging the Screen Layout PAN, Tilt and Zoom Controls Adjusting the Focus or Iris on a CameraControlling Cameras from the DX4000 Working with Presets To create a presetTo run a preset To run a predefined presetWorking with Patterns Using PresetTo set up a pattern To run a pattern Modifying Camera SettingsTo modify camera settings C2602M-A 6/06 Modifying Audio Settings To modify audio recording settingsTo modify live audio settings Modifying Image Recording Settings To modify image recording settingsModifying Alarms and Relays To modify alarm inputsTo modify relay outputs Setting UP a Recording Schedule Creating Recording SchedulesC2602M-A 6/06 Setting UP Motion Detection Recording Motion Detection Setup MenuC2602M-A 6/06 Setting UP ALARM-BASED Recording C2602M-A 6/06 Monitoring Live Video To change the screen modeTo view a specific video channel in single mode Working With Recorded Video Searching for VideoTimeline Showing Available Recorded Video C2602M-A 6/06 To back up video Playing Recorded VideoBacking UP Video Missing Media Warning Message Overview of the Main Screen Working With the Remote Agent ApplicationAbout the Remote Agent Remote Agent Control Buttons Starting and Stopping the Remote AgentTo start the remote agent To stop the remote agentConfiguring the Remote Agent To create a network connection for the DX4000Configuring the DX4000 from the Remote Agent To configure optional settings on the remote agentRecording Settings To set up recording qualityTo set up recording schedules Timer Recording Setup ScreenTo set up alarm recording To set up motion detectionC2602M-A 6/06 Camera Settings To configure camerasAudio Settings To set up audio recordingAlarm Settings To set up live audioSystem Settings To set up alarm inputs and relay outputsTo configure buzzer sounds To modify passwordsTo review system information To set the network speed To configure the disk write modeTo disconnect remote agent connections To control PTZ cameras To adjust the focusControlling Cameras from the Remote Agent To listen to or disable audio Monitoring Live Video from the Remote AgentCapturing Live Video from the Remote Client Controlling AudioUse the following buttons to review the recorded video Working with Recorded Video on the Remote AgentSearching for Recorded Video To search by date or time Click the Log button . The Search Log screen appearsTo search by event Event Viewer ScreenRemote Agent Backup Screen Backing UP VideoTo save a snapshot To print a snapshotSave as... dialog box appears Print screen appearsViewing Video with the Backup Player Click the Open file button. The following screen appears To view recorded video with the backup playerTo authenticate recorded video with the backup player About the Web Client Starting the WEB ClientClick the Connect button . The Login dialog box appears Monitoring Video with the Web ClientProduct Warranty and Return Information ISO9001
Related manuals
Manual 74 pages 2.6 Kb