Pelco C2602M-a manual To modify relay outputs

Page 35

To modify relay outputs

1.Select Alarm from the main menu, and then press the Enter button. The Alarm menu appears.

2.Select Relay Output Setup, and then press the Enter button. The Relay Output Setup menu appears.

Figure 39. Relay Output Setup Menu

3.For each alarm, modify the following relay settings:

•Select an alarm, and change its relay output to Enable or Disable.

•Change the relay mode to Latched or Transparent.

•For latched relays, select a duration. Durations can last as little as five seconds, as long as five minutes, or until an operator manually turns off the relay with a key (Until Key-In).

4.Select the Relay Type ﬁeld and set the relay to normally open (N/O) or normally closed (N/C).

5.After these settings are modiﬁed, press the Return button until all menus are cleared. A message appears stating that the settings are being saved.

C2602M-A (6/06)

35

Image 35

Contents DX4000 Digital Video Recorder Contents C2602M-A 6/06 List of Illustrations List of Tables Description Models FeaturesOverview of the System Connecting Devices to the DX4000Controls on the Front Panel of the DX4000 DX4000 ControlsControl Buttons on the Front Panel Video Control Buttons on the Front Panel of the DX4000Operating the DX4000 from the Remote Control To start the DX4000 Before You BeginStarting and Stopping the DX4000 To stop the DX4000 Table A. User Accounts and Access LevelsAll manager and operator access Choosing a User AccountMain Window Overview Changing the Information Displayed on the Monitor Changing the Display ModeTo change the screen sequencing mode Display Menu Adjusting Menu SettingsRecord Menu Audio Menu Camera MenuUse the Alarm menu to set up alarms and relays for cameras Alarm MenuSystem Menu System MenuBack UP Menu Backup MenuPassword Menu Changing PasswordsTo reset the passwords Resetting PasswordsFactory Default Reset Warning Message Factory Default SettingsScreen View Selection Screen Rotation ModeChanging the Screen Layout PAN, Tilt and Zoom Controls Adjusting the Focus or Iris on a CameraControlling Cameras from the DX4000 To run a predeﬁned preset Working with PresetsTo create a preset To run a presetWorking with Patterns Using PresetTo set up a pattern To run a pattern Modifying Camera SettingsTo modify camera settings C2602M-A 6/06 To modify audio recording settings Modifying Audio SettingsTo modify live audio settings To modify image recording settings Modifying Image Recording SettingsTo modify alarm inputs Modifying Alarms and RelaysTo modify relay outputs Creating Recording Schedules Setting UP a Recording ScheduleC2602M-A 6/06 Motion Detection Setup Menu Setting UP Motion Detection RecordingC2602M-A 6/06 Setting UP ALARM-BASED Recording C2602M-A 6/06 Monitoring Live Video To change the screen modeTo view a speciﬁc video channel in single mode Searching for Video Working With Recorded VideoTimeline Showing Available Recorded Video C2602M-A 6/06 To back up video Playing Recorded VideoBacking UP Video Missing Media Warning Message Overview of the Main Screen Working With the Remote Agent ApplicationAbout the Remote Agent To stop the remote agent Remote Agent Control ButtonsStarting and Stopping the Remote Agent To start the remote agentTo create a network connection for the DX4000 Configuring the Remote AgentTo conﬁgure optional settings on the remote agent Configuring the DX4000 from the Remote AgentTo set up recording quality Recording SettingsTimer Recording Setup Screen To set up recording schedulesTo set up motion detection To set up alarm recordingC2602M-A 6/06 To conﬁgure cameras Camera SettingsTo set up audio recording Audio SettingsTo set up live audio Alarm SettingsTo set up alarm inputs and relay outputs System SettingsTo conﬁgure buzzer sounds To modify passwordsTo review system information To set the network speed To conﬁgure the disk write modeTo disconnect remote agent connections To control PTZ cameras To adjust the focusControlling Cameras from the Remote Agent Controlling Audio To listen to or disable audioMonitoring Live Video from the Remote Agent Capturing Live Video from the Remote ClientUse the following buttons to review the recorded video Working with Recorded Video on the Remote AgentSearching for Recorded Video Click the Log button . The Search Log screen appears To search by date or timeEvent Viewer Screen To search by eventBacking UP Video Remote Agent Backup ScreenPrint screen appears To save a snapshotTo print a snapshot Save as... dialog box appearsViewing Video with the Backup Player Click the Open ﬁle button. The following screen appears To view recorded video with the backup playerTo authenticate recorded video with the backup player Starting the WEB Client About the Web ClientMonitoring Video with the Web Client Click the Connect button . The Login dialog box appearsProduct Warranty and Return Information ISO9001

Related manuals

Manual 74 pages 2.6 Kb