JVC HR-VP638U manual Basic Connections

Page 6

6INSTALLINGYOURNEWVCR

Basic Connections

Antenna or Cable

Coaxial Cable

Flat Feeder

ANTENNA-

IN (Antenna

AC Power

Matching Transformer

or Cable

 

input)

Cord

 

 

 

Back of VCR

RF

 

Video Cable

 

OUT

AC

(supplied)

 

Outlet

 

 

 

Audio Cable

 

 

(supplied)

 

 

CHECK CONTENTS

 

Make sure the package contains all of the accessories

1 listed in “SPECIFICATIONS” (pg. 56).

 

SITUATE VCR

2 Place the VCR on a stable, horizontal surface.

3

CONNECT VCR TO TV

The connection method you use depends on the type of

TV you have.

 

RF Connection

 

To Connect To A TV With NO AV Input Terminals . . .

 

a– Disconnect the TV antenna from the TV.

 

b– Connect the TV antenna cable to the ANT IN jack

 

on the rear of the VCR.

 

c– Connect the supplied RF cable between the RF

 

OUT jack on the rear of the VCR and the TV’s

 

antenna terminal.

AV Connection

To Connect To A TV With AV Input Terminals . . .

a– Connect the antenna, VCR and TV as shown in the illustration.

b– Connect an Audio/Video Cable (supplied) between the AUDIO OUT and VIDEO OUT jacks on the rear of the VCR and the AV IN jacks on the TV.

CONNECT VCR TO

POWER SOURCE

TV

RF Cable (supplied)

75 ohm terminal

4

Connect the power plug to an AC outlet.

 

The clock and tuner will automatically be set when

the antenna is connected and when the AC is first

 

connected to the VCR (pg. 7).

 

 

 

FINAL PREPARATION FOR

 

USE

 

Select the VCR channel (3 or 4) by setting the switch

5 on the rear of the VCR as shown in the illustration.

Back of VCR

/

CABLE

 

 

L

RF OUT

ON

BOX

 

 

 

 

CH3

CH4

Turn on the power to the TV. You are now able to perform

simple playback (pg. 22) and recording (pg. 23).

(If 'Auto' is displayed on the front display panel, the

clock is being set automatically. Wait for the time to be

displayed before powering on the VCR.)

NOTES:

The VCR channel is the channel on the TV which will display the audio and video signals from the VCR. The VCR's CH3- CH4 switch sets the VCR channel to CH3 or CH4.

The CH3–CH4 switch is preset to the CH3 position. Set to CH4 if CH3 is used for broadcasting in your area.

If your TV has no AV input terminals, set the channel on the TV to correspond to the CH3–CH4 switch on the back of the VCR.

Even if your TV has AV input terminals, you must connect it to the VCR using an RF cable in order to record one show while watching another (pg. 34).

For full identification of the VCR's rear panel, refer to the Index (REAR VIEW pg. 58).

Image 6
Contents HR-VP638U Dear Customer Do not place the VCRImportant Product Safety Instructions Product and cart combination Should be moved with care. QuickContents Basic Connections Dual Quick Set Perform Dual Quick SETDuring Auto Clock Set Language Clock Clock SET ScreenPreparation Semi-Auto Select Host ChannelSelect Time Zone Or Shuttle PlusMake Corrections Select D.S.T. ModeSelect Mode AutoAccess Band Screen Access Main MenuAccess Tuner SET TunerPerform Auto Channel SET Return to Normal ScreenMake Selection Access AFC ScreenAccess Manual Channel SET Screen Return to NormalAttach Controller Tuner Cable Box ControllerSituate Controller Connect Cable BOX to VCRAccess Cable BOX Output ScreenSet Cable Box Output Channel Turn on Cable BOX Select Cable BOX Output ChannelReturn to VCR PLUS+ SET-UP Screen Brand SET ScreenYou can now set up the VCR Plus+ feature pg VCR Plus+ Setup Access Main Menu ScreenPlus 5 to place ProcedurePress CH5 or Shuttle Arrow next to CustomInput Receiving Channel Number Simple Playback Simple Recording Still Picture/Frame-By- Frame Playback Pause During PlaybackActivate FRAME-BY Frame Playback Slow Motion/ Reverse Slow MotionVariable-Speed Search Reverse Play Activate VARIABLE-SPEED SearchActivate HIGH-SPEED Search High-Speed SearchRE-ENGAGE Automatic Tracking Engage Manual Tracking ModeAdjust Manual Tracking Manual TrackingAccess Function SET Access Audio MonitorSelect The Soundtrack Access Superimpose SuperimposeStart Repeat Access Distant CodeSkip Over Unwanted Sections Stop RepeatActivate Counter Reset Counter to ZeroActivate Instant Review MemoryNext-Function Memory Tape Position IndicatorMake Connection AV Compu Link PlaybackNext to Function SET, then press OK ExamplePress CH5 or Shuttle Plus 5 to place the arrow Arrow next to SpecialAuto Picture PlaybackSelect Channel for Viewing Engage TV ModeRecording Display Elapsed Time on ScreenTo Record SAP Programs Access 2ND AudioStereo And SAP Second Audio Program To Record Stereo ProgramsEnter Pluscode Number VCR Plus+ Timer ProgrammingAccess VCR PLUS+ Screen Check Input DataPress TIMER. The VCR turns off automatically Engage Timer ModePress just once to access the Auto Timer screen CHECK/CORRECT Input DataInstant Timer Recording ITR On-Screen Timer ProgrammingSET Program Information Shuttle Plus 5 buttonRE-ENGAGE Timer Disengage TimerCancel a Program Check And Cancel ProgramsYour choice on or Access Auto TimerAuto Timer OFF by pressing CHEdit From a Camcorder Access AUX Input Screen Start RecorderShuttle Plus 5. If Load Cassettes SET RECORDER’S Input ModeEdit To Or From Another Start PlayerAssemble Editing Locate END Point SET Input ModeReset the Counter Locate Start PointEngage Insert Editing END Insert EditingStart Dubbing Audio DubbingEngage Audio Dubbing END Audio DubbingTurn on the TV SET Remote Control ModeTV Multi-Brand Remote Control SET TV Brand CodeEnter Cable BOX Brand Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Operate Cable BOXPlug in Power Cord Unplug Vcrs PowerSET A/B Code Switch Turn VCR Power onCassette gets stuck partway Make sure the window side is up,Timer again RecordingRe-perform the VCR Plus+ setup Procedure pgDoesn’t work properly Questions and Answer S 20C to 60C -4F to140F EIA monochrome signalYear programmable timer Maximum recording timeMBR Multi-Brand Remote Code Setting VCR Plus+ Timer ProgrammingList Of Terms Front View Remote Control Provided Front Display PanelFor Servicing Warranty EMO Page HR-VP638U