JVC HR-J638E/EH specifications Activate Counter, Memory, SET A/B Code Switch, RE-SUPPLY Power

Page 13

Tape Remaining Time

DISPLAY REMAINING TIME

1 Press DISPLAY until the time remaining on the tape appears.

By pressing the DISPLAY button, you can change the display to show the counter reading, tape remaining time, or clock time.

NOTE:

Depending on the type of tape used, there may be times when the tape remaining time reading may not appear right away, or is not correct. "- - : - -" may sometimes appear, or the display may blink on occasion.

Counter Memory

Returns to the counter reading of “0:00:00” to conveniently find a specific place on the tape automatically.

1

SET COUNTER MEMORY

Press C. RESET during playback at a point you wish to

locate later. The counter reads “0:00:00”. Then press C.

MEMORY, and “M” appears in front of the counter digits.

 

ACTIVATE COUNTER

2

MEMORY

When you wish to return to the designated point, press

STOP and then REW or FF.

The tape rewinds or fast-forwards and stops at about

 

 

0:00:00 automatically.

 

To cancel Counter Memory, press C.MEMORY again.

EN13

Remote A/B Code Switching

The remote control is capable of controlling two JVC video recorders independently; one set to respond to the remote control’s A code control signals and another set to respond to B code control signals. The remote control is preset to send A code signals because your video recorder is initially set to respond to A code signals. You can easily modify your video recorder to respond to B code signals.

1

 

REMOVE POWER SUPPLY

 

Unplug the mains power cord from the mains outlet.

2

 

SET A/B CODE SWITCH

 

Set to B.

3

 

RE-SUPPLY POWER

 

Plug the mains power cord back into the mains outlet.

4

 

TURN THE RECORDER ON

 

Press OPERATE on the remote control. The recorder

 

will now only respond to B code signals.

 

 

 

NOTE:

Some TV sets may malfunction in response to the B mode. If this happens, switch back to the A mode.

Soundtrack Selection

Your video recorder is capable of recording three soundtracks (HI-FI L, HI-FI R and NORM) and will play back the one you select.

During Playback

Pressing AUDIO MONITOR on the remote control changes the soundtrack being played back as follows:

TRACK

 

 

 

 

 

USE

Recorder's Front Panel

On-Screen Display

 

 

 

 

 

 

 

 

 

L + R

 

 

HI FI

For Hi-Fi stereo tapes

 

L

 

 

 

 

R

 

 

 

 

 

 

 

 

 

 

 

 

L

L

 

HI FI

For main audio of Bilingual tapes

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R

 

 

HI FI

For sub audio of Bilingual tapes

 

 

 

 

 

 

R

 

 

 

 

 

NORM

 

NORM

For audio-dubbed tapes

 

 

 

 

 

 

 

 

L + R + NORM

 

 

HI FI

For audio-dubbed tapes

 

 

NORM

 

NOTES:

"L + R" should normally be selected. In this mode, Hi-Fi stereo tapes are played back in stereo, and the NORM track is played back automatically for tapes with only normal audio.

For instructions on recording stereo and bilingual programmes, refer to page 18.

"O.S.D." must be set to "ON" or the on-screen displays will not appear (pg. 17).

Image 13
Contents HR-J638E/EH Safety First Safety PrecautionsDo not place the recorder Tune The TV To Your Video Recorder Basic ConnectionsConnecting Using a Decoder Tuner Set Initial Settings ENSelect Language Select CountryView Confirmation Screen Initial SettingsReturn to Normal Screen USHPreparation Clock SetSET Date and Time SET ClockSET Just Clock Channel PositionLoad a Cassette Basic PlaybackPoint Start PlaybackPause During Playback Playback FeaturesActivate HIGH-SPEED Search Override Automatic Tracking Adjust TrackingManually Return to AutomaticStop Scene Finder Activate Scene FinderActivate Index Search EN PlaybackRE-SUPPLY Power SET A/B Code SwitchActivate Counter MemoryBasic Recording S.T. Picture System Access Mode SelectRecording Playback On-Screen Displays ENABLE/DISABLEEN Recording Recording FeaturesReceiving Stereo And Bilin- gual Programmes To Record Stereo And Bilin- gual Programmes A2Engage ITR Mode Reset CounterSelect Channel to Watch SET Counter DisplayEN Timer Recording Access CH. SET Mode Menu ScreenInformation On ShowView Make List of Stored Station Names Channel PositionsEnter Showview Number When Using a Satellite TunerClose Menu PreparationEN Timer RECORDINGcont ShowView Timer RecordingTo re-engage the timer, press Timer To Delay The Stop Time Timer ModeTo Timer-Record Weekly Or Daily Serials Return to NormalEngage RECORDER’S Timer Mode Regular Timer ProgrammingEnter Programme Stop Time Timer Access Programme ScreenRevise Programme IN- Formation Engage Auto SP/LPEdit To Or From Another Video Recorder SET Recording DECK’S Input ModeMake Connections Start Source PlayerEdit From a Camcorder SET RECORDER’S Input ModeStart Camcorder Start RecorderAudio Dubbing OUT or AV2 in connector. When using these connectors When monitoring the sound during Audio Dubbing,Make sure to select the correct input mode in step Priority over those made to the rear panel connectorsMulti-Brand Remote Con- trol Control Your TV Using Addi- tional ButtonsSET TV Brand Code TRY Operating TVSelect Mode Access CH. SET ModeMenu Select PositionPerform Tuning Switch StationsSelect NEW Station Select Channel toTV Station and ID List Clear Corrective ActionPossible Cause Timer againTape-to-tape editing is not possible Questions and Answers Front View Index@ # Indicator will blink during turbo searchHow To Use Installing BatteriesMaximum recording time PAL-type colour signal and Ccir monochrome signal,625 lines