JVC HR-J673EU instruction manual 52 EN, Other Problems

Page 52

52 EN			TROUBLESHOOTING (cont.)
OTHER PROBLEMS
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Whistling or howling is heard from the	● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

2.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them ( pg. 42).

3.	The channel cannot be changed.	● Recording is in progress.	Press 9 to pause the recording, change
			channels, then press 4 to resume
			recording.

4.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

5.	No channels are stored in the	● The TV aerial cable was not connected	Connect the TV aerial cable to the
	recorder’s memory.	to the recorder when Auto Set Up was	recorder properly and turn off the recorder
		performed.	power once, then turn the recorder power
			back on again. The recorder will try Auto
			Set Up again ( pg. 8).

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 52

Contents Video Cassette Recorder English Safety Precautions Moisture Condensation Front View Front Display Panel How To Use Operating JVC TVsCheck the contents Situate the recorderConnect the recorder to TV Connect the recorder to mainsTurn on the recorder Auto Set UpSelect your country Perform Auto Set Up Select the languagePress rt to select your language code Press rt to select Auto and press OK or ePerform Preset Download 10 ENSet the video channel Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockAccess the Main Menu screen Access the Country Set screenLanguage 12 ENInstalling Satellite Controller Situate the Satellite ControllerAttach the Satellite Controller Make connectionsSetting satellite receivers brand and channel 14 ENNexTView Link TV Auto Power OnVCR Auto Standby Direct Rec Basic Playback 16 ENSlow Motion High-Speed SearchVariable Speed Search Pause during playbackManual Tracking 18 ENInstant ReView Index Search Skip SearchNext Function Memory Repeat Playback20 EN Instant Timer Recording ITR Engage the ITR modeWatching Another Set the recording durationReset the counter 22 ENTape Remaining Time Set the counter displayPlayback RecordingAccess the Showview screen Access the Showview Program screenBefore performing the Showview Timer Programming 24 ENSet the VPS/PDC mode Engage the recorder’s timer modeSatellite Receiver Users Guide Program Number SetExpress Timer Programming 26 ENTo Timer-Record Weekly Or Daily Serials VPS/PDC RecordingEnter the channel position Press PR +28 EN Cancel or change programme setting Confirm the overlapping programmesSelect the programme to modify Overlapping programmes blink on the TV screenSelect the L-2 Select mode Engage the Auto Satellite Programme Recording modeProgramme Recording 30 ENSet the recorder’s input mode Set the edit modeEdit From a Camcorder Start the camcorderSet the input mode of recording deck Another Video Recorder32 EN Start the source playerConnecting To a Satellite Receiver Satellite receiver Decoder Back of recorderSelect the input mode 34 ENConnect the decoder Set the tunerHR-J670/672/673EU only Make connectionsMode Set Access the Mode Set screenSelect the mode Select the mode settingYou can set the B.E.S.T. Biconditional Equalised Signal This feature helps you to adjust the playback pictureWhen this function is set to ON, the timer is Off, and automatically disengaged when the recorder is38 EN For ExampleAbout Ntsc Playback Access the Auto Channel Set screen Tuner Set40 EN Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK twice 42 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a ChannelSet Stations a 44 ENSet Stations B TV Station And ID List Station NameAccess the Video Channel Set mode Exit the Video Channel Set modeVideo Channel Set 46 ENShowview Setup Guide Program Number SetGuide Program Number Enter the Guide Program numberClock Set Access the Clock Set screen48 EN Set the date and time Set Just ClockSet the source channel position for clock data Start the clock operationTroubleshooting 50 ENRecording Other Problems 52 ENPlayback 54 EN Auto Set Up Connecting To a Satellite Receiver Delete a ChannelLanguage Manual Channel Set Manual Tracking Mode Set Timer warning display Tuner SetCountry Code International Telephone Language CodeSee Instructions pg

Related manuals

Manual 56 pages 11.98 Kb