JVC HR-J770EK Video Plus+ Timer Programming, Access Video PLUS+ Screen, Enter Pluscode Number

Page 16

16BASICOPERATIONS(cont.)

VIDEO Plus+

Timer

Programming

Before performing VIDEO Plus+ Timer Programming:

●Make sure that the recorder's built-in clock is set properly.

●Insert a cassette with the safety tab in place. The recorder will come on automatically.

●Turn on the TV and select the VIDEO channel (or AV mode).

With VIDEO Plus+, timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise.

ACCESS VIDEO PLUS+ SCREEN

1	Press PROG.		VIDEO PLUS+
	Press PROG.



		[0 – 9] = VIDEO PLUS+
		[+/–] : EXPRESS PROGRAMING
		[PROG] : EXIT

The front display panel looks like this:

ENTER PLUSCODE NUMBER

	Press the NUMBER keys to	VIDEO PLUS+
	enter the PlusCode	VIDEO PLUS+
	enter the PlusCode	1 2 3 4 5 6 7 8
	2 number of the programme	1 2 3 4 5 6 7 8
	2 number of the programme
	you wish to record.

●If you make a mistake, press and input the

2

NUMBER

5 PDC

STOP+/–

1

1,6 PROG

1 2

4 5

78 0

?

– –:– –

DAILY	WEEKLY
3

2

6

9

4 7

SP/LP 4

correct number.	[0 – 9] =
	[ ] : DELETE
	[PROG] : EXIT

The PlusCode number you enter appears on the front display panel:

The display panel shows only a 4-digit number.

ACCESS VIDEO PLUS+ PROGRAM SCREEN

	Press OK, and the VIDEO		– P1 –
	Plus+ Program screen	VIDEO PLUS+ 123456789
3 appears (if you’re just		START	STOP
3 appears (if you’re just		21:00	= 22:00
	starting out, “P1” appears).	SP	VPS/PDC OFF
		SP	VPS/PDC OFF
	The display panel shows the	DATE	TV PROG
	programme start time.	25.12	1
			BBC 1

3

OK 3,6

Pressing	changes the
display to the programme
display to the programme		: OK	[0]:SAT
stop time, then the date and
preset position.

	SP

IMPORTANT

Make sure the preset position number you wish to record is displayed; if not, see "VIDEO Plus+ Setup" on page 39 and set the Guide Program number for that PlusCode number correctly.

●If the number you entered is invalid, "ERROR" appears on the screen and "Err" appears on the display panel. Press and input a valid PlusCode number.

●If the "GUIDE PROG SET" screen appears, see "ATTENTION – Regarding Guide Program Number Set" on page 17.

Image 16

Contents HR-J770EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide To connect to a TV with 21-pin AV input connector Scart Back of TVTV Aerial Cable not provided Back of RecorderBefore performing the following procedure, make sure that Auto for Auto Set Up functionRefer to Tion pg and the TV is turned on,Or remote control until the display panel Shows either the display as illustrated onProgress, this process will be interrupted You will need to start again. See Notes belowIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedTV Auto Power On Link FunctionsTurn on the Recorder NexTView LinkSatellite Receiver Control Setting Enter Satellite RECEIVER’S Brand Access SAT Control SET ScreenCheck Result of Test Playback Load a CassetteFind Programme Start Point Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Access Video PLUS+ ScreenAccess Video PLUS+ Program Screen Enter Pluscode NumberTimer Warning PDC RecordingExpress Timer Programming Before performing Express Timer ProgrammingEnter Programme Start Time TimeSET PDC Mode Timer ModeReturn to Normal Engage RECORDER’SCheck, Cancel And Replace Programmes Cancel or Replace a ProgrammeReturn to Timer Mode Return to Normal SCREEN/ DisplayWhen programmes overlap each other Cancel or Change Programme SettingTo cancel a programme Confirm Overlapping ProgrammesPlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemPlayback RecordingOr press Record on the recorder Looking For Scene You Want Skip Over UnwantedSections Activate Index SearchSelecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackAerial Pin AV input Connector Scart Automatic Satellite Programme RecordingSatellite Receiver Unit TV Aerial cableAccess Main Menu Screen Playback Picture Adjustment Adjust TrackingOverride Automatic Tracking ManuallyAccess Main Menu Screen Access Mode SET ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingSET RECORDER’S Input Mode SET Edit ModeEdit From Camcorder Start CamcorderInput Mode Edit To Or From Another Video RecorderSET Recording DECK’S Start Source PlayerTo the AV2 L-2 IN/DECODER connector Select SettingOff. pg Other Functions ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Display Power Save Mode Power SAVE, then pressAuto SP→LP Timer Auto TimerNext Function Memory Ntsc Playback Repeat PlaybackActivate Repeat Playback Connection To Stereo System Audio Cable not provided SpeakerClock Set Just ClockNumber Video Plus+ SetupGuide Program Number Set Access Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Perform Auto Channel SET Tuner SetAuto Channel Set Screen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Select BandInput Channel Enter NEW Channel InformationWhen Receiving a Scrambled Broadcast Change Station Preset PositionFine-Tuning Channels Already Stored Delete a ChannelAccess Manual Switch StationsChannel SET Screen Select NEW StationTV Station And ID List TV Station Channel Number Guide Ä remain lit on the display panel. Is there Problem? Questions And AnswersWhat happens if the tape runs out during recording? Troubleshooting Timer Recording Won’t stopIndex Front ViewAudio OUT L/R Connectors enable Symbolic Mode IndicatorsProgramme Time Indicators show the programme Tape Speed Indicators display mode of recording lightRemote Control Fast Forward FF Button fast-forwards tape VCR, TV PR +/-,TV +/-, TV MutingJ770EK Maximum recording timeDA4 Double Azimuth helical VHF 44.5 143/143 470 MHz