JVC HR-J770EK Maximum recording time, DA4 Double Azimuth helical, VHF 44.5 143/143 470 MHz

Page 56

SPECIFICATIONS

GENERAL

Power requirement	: AC 220 – 240 V`, 50/60 Hz
Power consumption
Power on	: 19 W
Power off	: 4.9 W
Temperature
Operating	: 5°C to 40°C
Storage	: –20°C to 60°C
Operating position	: Horizontal only
Dimensions (WxHxD)	: 400 x 94 x 281 mm
Weight	: 3.5 kg
Format	: VHS PAL standard
Maximum recording time
(SP)	: 240 min. with E-240 video
	cassette
(LP)	: 480 min. with E-240 video
	cassette
VIDEO/AUDIO
Signal system	: PAL-type colour signal and
	CCIR monochrome signal,
	625 lines/50 fields
Recording system	: DA4 (Double Azimuth) helical
	scan system
Signal-to-noise ratio	: 45 dB
Horizontal resolution	: 250 lines
Frequency range	: 70 Hz to 10,000 Hz (Normal
	audio)
	20 Hz to 20,000 Hz (Hi-Fi
	audio)
Input/Output	: 21-pin SCART connectors
	(IN/OUT x 1,
	IN/DECODER x 1)
	RCA connectors
	(VIDEO IN x 1, AUDIO IN x 1,
	AUDIO OUT x 1)

TUNER/TIMER
TV channel storage
capacity	: 99 positions
	(+AUX position)
Tuning system	: Frequency synthesized tuner	HR-
Channel coverage	: VHF 44.5 – 143/143 – 470 MHz
	UHF 470 – 862 MHz
Aerial output	: UHF channels 22 – 69
	(Adjustable)	J770EK
Memory backup time	: Approx. 10 min.
ACCESSORIES
Provided accessories	: RF cable,
	Satellite Controller,
	Infrared remote control unit,
	"AA" battery x 2

Specifications shown are for SP mode unless otherwise specified.

E.& O.E. Design and specifications subject to change without notice.

VICTOR COMPANY OF JAPAN, LIMITED

COPYRIGHT © 1999 VICTOR COMPANY OF JAPAN, LTD.

	EK	Printed in Malaysia
	EK	1199IYVIDPJ
		1199IYVIDPJ

Image 56

Contents HR-J770EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide To connect to a TV with 21-pin AV input connector Scart Back of TVTV Aerial Cable not provided Back of RecorderBefore performing the following procedure, make sure that Auto for Auto Set Up functionRefer to Tion pg and the TV is turned on,Or remote control until the display panel Shows either the display as illustrated onProgress, this process will be interrupted You will need to start again. See Notes belowIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedTV Auto Power On Link FunctionsTurn on the Recorder NexTView LinkSatellite Receiver Control Setting Check Result of Test Access SAT Control SET ScreenEnter Satellite RECEIVER’S Brand Playback Load a CassetteFind Programme Start Point Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Access Video PLUS+ ScreenAccess Video PLUS+ Program Screen Enter Pluscode NumberTimer Warning PDC RecordingExpress Timer Programming Before performing Express Timer ProgrammingEnter Programme Start Time TimeSET PDC Mode Timer ModeReturn to Normal Engage RECORDER’SCheck, Cancel And Replace Programmes Cancel or Replace a ProgrammeReturn to Timer Mode Return to Normal SCREEN/ DisplayWhen programmes overlap each other Cancel or Change Programme SettingTo cancel a programme Confirm Overlapping ProgrammesPlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemOr press Record on the recorder RecordingPlayback Looking For Scene You Want Skip Over UnwantedSections Activate Index SearchSelecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackAerial Pin AV input Connector Scart Automatic Satellite Programme RecordingSatellite Receiver Unit TV Aerial cableAccess Main Menu Screen Playback Picture Adjustment Adjust TrackingOverride Automatic Tracking ManuallyAccess Main Menu Screen Access Mode SET ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingSET RECORDER’S Input Mode SET Edit ModeEdit From Camcorder Start CamcorderInput Mode Edit To Or From Another Video RecorderSET Recording DECK’S Start Source PlayerOff. pg Select SettingTo the AV2 L-2 IN/DECODER connector On-Screen Display ENABLE/DISABLE ON-SCREEN DisplayOther Functions Power Save Mode Power SAVE, then pressNext Function Memory Auto TimerAuto SP→LP Timer Activate Repeat Playback Repeat PlaybackNtsc Playback Connection To Stereo System Audio Cable not provided SpeakerClock Set Just ClockGuide Program Number Set Video Plus+ SetupNumber Access Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Auto Channel Set Tuner SetPerform Auto Channel SET Screen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Select BandInput Channel Enter NEW Channel InformationWhen Receiving a Scrambled Broadcast Change Station Preset PositionFine-Tuning Channels Already Stored Delete a ChannelAccess Manual Switch StationsChannel SET Screen Select NEW StationTV Station And ID List TV Station Channel Number Guide What happens if the tape runs out during recording? Questions And AnswersÄ remain lit on the display panel. Is there Problem? Troubleshooting Timer Recording Won’t stopIndex Front ViewAudio OUT L/R Connectors enable Symbolic Mode IndicatorsProgramme Time Indicators show the programme Tape Speed Indicators display mode of recording lightRemote Control Fast Forward FF Button fast-forwards tape VCR, TV PR +/-,TV +/-, TV MutingJ770EK Maximum recording timeDA4 Double Azimuth helical VHF 44.5 143/143 470 MHz