JVC HR-J770EK setup guide Access Main Menu Screen

Page 27

27

– –:– –

SATä indicator

ATTENTION

●Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on.

●If you have connected another appliance other than a satellite receiver to the AV2 (L-2) IN/DECODER connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on.

●Auto Satellite Prog recording and timer-recording cannot be done at the same time.

●When you press and hold the recorder's SATäbutton to engage the Auto Satellite Prog Rec mode, if the SATä indicator does not light but instead blinks quickly even though your satellite receiver's power is off, Auto Satellite Prog Recording will not work properly with that satellite receiver*.

If this is the case, perform "Express Timer Programming" (☞ pg. 18) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Auto Satellite Prog Recording is not possible with those satellite receivers.

NOTES:

Before performing the following steps:

●Make sure the satellite receiver is connected to the recorder's AV2 (L-2) IN/DECODER connector. (☞ pg. 26)

●Programme the timer on the satellite receiver.

●Insert a cassette with the safety tab in place.

ACCESS MAIN MENU SCREEN

1 Press MENU.

 

 

 

 

 

 

 

ACCESS MODE SET SCREEN

 

 

 

 

Move the highlight bar (pointer) to "MODE SET" by

2 pressing %Þ, then press OK or #.

 

 

 

3

SELECT L-2 SELECT MODE

 

 

 

Move the highlight bar (pointer) to "L-2 SELECT", by

pressing %Þ, then press OK or #to set to "SAT" or "L-2".

Then press MENU.

 

 

 

 

 

 

 

 

MODE SET

 

 

PREVIOUS PAGE

 

 

 

 

 

 

 

 

 

 

 

 

 

B. E. S. T.

ON

 

 

 

 

 

 

 

L-2 SELECT

SAT

 

 

PICTURE CONTROL

AUTO

 

 

 

 

 

 

 

AUTO TIMER

OFF

 

 

 

 

 

 

O. S. D.

ON

 

 

 

 

 

 

DIRECT REC

ON

 

 

 

 

 

 

AUTO SP=LP TIMER

OFF

 

 

 

 

 

 

POWER SAVE

OFF

 

 

 

 

 

 

NEXT PAGE

 

 

 

 

 

 

 

[5°] =

 

 

[5°] =

 

 

 

 

 

[MENU] : EXIT

 

 

[MENU] : EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

SET TAPE SPEED

 

 

 

 

4 Press SP/LP ( ) to set the tape speed.

 

 

 

 

ENGAGE AUTO SATELLITE PROG

 

REC MODE

 

 

 

 

 

 

 

Press and hold SATä for about 2 seconds. The SATä

 

indicator lights up and the recorder turns off automati-

5 cally.

 

 

 

 

 

 

●To disengage the Auto Satellite Prog Rec mode, press SATä. The SATä indicator goes off.

●If the recorder's power is off, it is not possible to engage the Auto Satellite Prog Rec mode.

●Auto Satellite Prog recording is possible with the AV2 (L-2) IN/DECODER connector only.

●When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON".

●After Auto Satellite Prog recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function (☞ pg. 24).

●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

●Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer.

●The SAT ä indicator blinks while Auto Satellite Prog recording is in progress.

●Pressing the recorder's button while Auto Satellite Prog recording is in progress turns off the recorder's power and disengages the Auto Satellite Prog Rec mode.

●If there is more than one satellite programme you wish to record with Auto Satellite Prog Recording, it is not possible to set a different tape speed for each; the tape speed selected in step 4 will apply to all the programmes for Auto Satellite Prog recording.

●The B.E.S.T. system (☞ pg. 22) does not work while Auto Satellite Prog recording is in progress.

●Just Clock (☞ pg. 38) does not work when the Auto Satellite Prog Rec mode is engaged.

●Depending on the type of satellite receiver, the recorder may not record a short portion at the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Auto Satellite Prog Rec mode when the satellite receiver's power is on, the recorder will not start Auto Satellite Prog recording even though the SAT ä indicator blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

●You can also record a programme from your cable system in the same way if the system has a timer and is connected to the recorder's AV2 (L-2) IN/DECODER connector.

Page 26 Page 28
Image 27
Page 26 Page 28
Contents HR-J770EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of Recorder To connect to a TV with 21-pin AV input connector ScartBack of TV TV Aerial Cable not providedTion pg and the TV is turned on, Before performing the following procedure, make sure thatAuto for Auto Set Up function Refer toYou will need to start again. See Notes below Or remote control until the display panelShows either the display as illustrated on Progress, this process will be interruptedIf both auto channel set and auto clock set have failed If auto channel set has succeeded but auto clock set has notNexTView Link TV Auto Power OnLink Functions Turn on the RecorderSatellite Receiver Control Setting Access SAT Control SET Screen Enter Satellite RECEIVER’S BrandCheck Result of Test Start Playback PlaybackLoad a Cassette Find Programme Start PointActivate HIGH-SPEED Search Pause During PlaybackRecording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeEnter Pluscode Number Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Access Video PLUS+ Program ScreenPDC Recording Timer WarningTime Express Timer ProgrammingBefore performing Express Timer Programming Enter Programme Start TimeEngage RECORDER’S SET PDC ModeTimer Mode Return to NormalReturn to Normal SCREEN/ Display Check, Cancel And Replace ProgrammesCancel or Replace a Programme Return to Timer ModeConfirm Overlapping Programmes When programmes overlap each otherCancel or Change Programme Setting To cancel a programmeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsRecording PlaybackOr press Record on the recorder Activate Index Search Looking For Scene You WantSkip Over Unwanted SectionsDuring Playback Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionTV Aerial cable Aerial Pin AV input Connector ScartAutomatic Satellite Programme Recording Satellite Receiver UnitAccess Main Menu Screen Manually Playback Picture AdjustmentAdjust Tracking Override Automatic TrackingMinimizing Picture Degradation While Editing Access Main Menu ScreenAccess Mode SET Screen Select Picture Control SET ModeStart Camcorder SET RECORDER’S Input ModeSET Edit Mode Edit From CamcorderStart Source Player Input ModeEdit To Or From Another Video Recorder SET Recording DECK’SSelect Setting To the AV2 L-2 IN/DECODER connectorOff. pg ENABLE/DISABLE ON-SCREEN Display Other FunctionsOn-Screen Display Power SAVE, then press Power Save ModeAuto Timer Auto SP→LP TimerNext Function Memory Repeat Playback Ntsc PlaybackActivate Repeat Playback Audio Cable not provided Speaker Connection To Stereo SystemJust Clock Clock SetVideo Plus+ Setup NumberGuide Program Number Set SET Video Channel Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Tuner Set Perform Auto Channel SETAuto Channel Set Is displayed on the screen Screen preset positionsProcedures After Scan CompletedEnter NEW Channel Information Storing Channels ManuallySelect Band Input ChannelDelete a Channel When Receiving a Scrambled BroadcastChange Station Preset Position Fine-Tuning Channels Already StoredSelect NEW Station Access ManualSwitch Stations Channel SET ScreenTV Station And ID List TV Station Channel Number Guide Questions And Answers Ä remain lit on the display panel. Is there Problem?What happens if the tape runs out during recording? Troubleshooting Won’t stop Timer RecordingFront View IndexTape Speed Indicators display mode of recording light Audio OUT L/R Connectors enableSymbolic Mode Indicators Programme Time Indicators show the programmeRemote Control VCR, TV PR +/-,TV +/-, TV Muting Fast Forward FF Button fast-forwards tapeVHF 44.5 143/143 470 MHz J770EKMaximum recording time DA4 Double Azimuth helical
Top Page Image Contents