JVC HR-S4500U manual Roubleshooting, Timer again

Page 62

62EN

TROUBLESHOOTING(cont.)

TIMER RECORDING

 

 

 

 

 

 

 

 

 

 

 

SYMPTOM

 

POSSIBLE CAUSE

 

CORRECTIVE ACTION

1.

Timer recording won’t work.

 

● The clock and/or the timer have

 

Set the clock and/or timer correctly.

 

 

 

been set incorrectly.

 

 

 

 

 

● The timer is not engaged.

 

Press TIMER and check to make sure

 

 

 

 

 

that ä appears on the front display

 

 

 

 

 

panel.

 

 

 

● The VCR has not been set up properly.

 

Re-perform the set-up procedures.

 

 

 

 

 

Make sure you have compensated for

 

 

 

 

 

Guide Channel and VCR or cable

 

 

 

 

 

box channel number mismatches

 

 

 

 

 

(☞ pg. 43).

 

 

 

 

 

 

2.

Timer programming won’t work.

 

● Timer recording is in progress.

 

Timer programming can’t be performed

 

 

 

 

 

when timer recording is in progress.

 

 

 

 

 

Wait until it finishes.

 

 

 

 

 

 

3.

ä and ] on the front display

 

● The timer is engaged but there’s no

 

Load a cassette with the record safety

 

panel won’t stop blinking.

 

cassette loaded.

 

tab intact, or with the hole covered

 

 

 

 

 

with adhesive tape.

 

 

 

 

 

 

4.

The cassette is automatically

 

● The loaded cassette has had its

 

Remove the cassette and cover its

 

ejected, and ä and ] on the

 

record safety tab removed.

 

hole with adhesive tape, or replace it

 

front display panel won’t stop

 

 

 

with a cassette on which the safety

 

blinking.

 

 

 

tab is intact.

 

 

 

 

 

 

5.

ä blinks for 10 seconds and the

 

● TIMER has been pressed when there

 

Check the programmed data and re-

 

timer mode is disengaged.

 

are no programs in memory, or the

 

program as necessary, then press

 

 

 

timer record program information

 

TIMER again.

 

 

 

has not been programmed correctly.

 

 

 

 

 

 

 

 

6.

The cassette is automatically

 

● The end of tape was reached during

 

The program may not have been

 

ejected, the power shuts off and ä

 

timer recording.

 

recorded in its entirety. Next time

 

and ] won’t stop blinking.

 

 

 

make sure you have enough time on

 

 

 

 

 

the tape to record the entire program.

 

 

 

 

 

 

7.

Cable channels are not automatically

 

● The Controller is not properly

 

Connect the Controller correctly

 

switched during timer recording.

 

connected to the VCR.

 

(☞ pg. 16).

 

 

 

● The output channel selected in the

 

After confirming your cable box’s

 

 

 

Cable Box Set screen is incorrect.

 

output channel number, re-access the

 

 

 

 

 

Cable Box Set screen and select the

 

 

 

 

 

correct number (☞ pg. 17).

 

 

 

● The cable box’s power is off.

 

Make sure the power is on before

 

 

 

 

 

timer recording starts.

 

 

 

 

 

 

8.

Satellite channels are not automati-

 

● The Controller is not properly

 

Connect the Controller correctly

 

cally switched during timer

 

connected to the VCR.

 

(☞ pg. 19).

 

recording.

 

● The output channel selected in the

 

After confirming your DBS receiver’s

 

 

 

DBS Receiver Set screen is incorrect.

 

output channel number, re-access the

 

 

 

 

 

DBS Receiver Set screen and select

 

 

 

● The VCR is not set correctly to

 

the correct number (☞ pg. 20).

 

 

 

control the DBS Receiver

 

Set the correct DBS Receiver brand

 

 

 

● The DBS receiver’s power is off.

 

code (☞ pg. 21).

 

 

 

 

 

Make sure the power is on before

 

 

 

 

 

timer recording starts.

 

 

 

 

 

 

9.

Timer recording begins as sched-

 

● Even though you don't use an

 

Set "CABLE BOX SET" to "OFF"

 

uled, but the channel is always

 

external Cable Box, "CABLE BOX

 

(☞ pg. 17).

 

incorrect.

 

SET" is set to "ON".

 

 

 

 

 

 

 

10.We moved, and now VCR Plus+

 

● The receivable stations in the new area

 

Re-perform the VCR Plus+ setup

 

doesn’t work properly.

 

are received on different channels than

 

procedure (☞ pg. 43).

 

 

 

those in the previous area.

 

 

 

 

 

 

 

 

11.

“PROGRAM FULL” is displayed on

 

● All 8 programs of the VCR’s timer

 

Wait until a space in memory clears,

 

the screen.

 

memory are used.

 

or cancel unnecessary program

 

 

 

 

 

information (☞ pg. 47).

 

 

 

 

 

 

 

 

 

 

 

 

Page 61 Page 63
Image 62
Page 61 Page 63
Contents HR-S4500U Dear Customer Do not place the VCRPower Lines Power SourcesPower Cord Protection Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsContents Connections Matching Transformer not supplied Connect VCR to TVEN I Nitial Sett Ings Plug & Play SetupPlug & Play Auto Clock Set/Auto Tuner SetInformation Language Preparation Access Clock SET ScreenClock Scan #Select Host Channel Select D.S.T. ModeSET Auto Clock to on Semi-AutoSET Time Select Time ZoneReturn to Normal Screen SET DateSET Access Main Menu ScreenTuner Set Receivable ChannelsAdd Or Delete a Channel Access ManualChannel Time Scan #Attach Controller Cable Box ControlSituate Controller Connect Cable BOX to VCRSelect Cable BOX Access Cable BOX SETTurn on Cable BOX Output ChannelBrand Code Access Cable BOX Brand SET ScreenEnter Cable BOX Brand Connect DBS Receiver To VCR Fasten securely using the supplied adhesive stripsDBS Receiver Control DBS receiverSet DBS Receiver Output Channel & DBS Receiver Brand Turn on DBS ReceiverSelect DBS Receiver JVC Dish Network Echostar Dish Network Access DBS ReceiverDBS Receiver Code from Following list, then Press OK JVCFind Program Start Point Simple PlaybackLoad a Cassette Start PlaybackSimple Recording EN Playba CK and Recording Feat Ures Playback FeaturesActivate FRAME-BY Frame Playback Still Picture/Frame-By- Frame PlaybackAdjust Manual Tracking Access Distant CodeEngage Manual Tracking Mode Start SearchCH 5 or Time Scan Playb a CK and Recording FeaturesVideo Stabilizer Time Scan #to set toStop Repeat Reset Counter to ZeroStart Repeat Activate Instant ReviewMode SuperimposeSelect The Soundtrack SET ModeSelect Audio Monitor Advance Access Skip MenuPerform Movie Movie AdvanceAV Compu Link Playback ExampleActive Video Calibration Video CalibrationPlayback RecordingRecording Features VHS Super VHS, S-VHS ET and VHS Super VHS ET Select S-VHS ET SET ModeEngage S-VHS ET Mode Stereo And SAP Second Audio Program Access Function SET ScreenSelect 2ND Audio Record SET Mode To Record SAP ProgramsTime Scan Audio signal during TimeScanOutput audio signal is normal monaural sound Variable-Speed Search/ Reverse Motion PlaybackSpeed Audio output Skip Over Unwanted SectionsSkip Search Reverse Forward Search Play Slow-Motion Still × -5×-3×TimeScan Audio Place MenuNumber VCR Plus+ Timer ProgrammingTimer Recording Check Program Data Engage Timer ModeEN Timer Recording Initial SET, then press VCR Plus+ SetupVCR Plus+ Guide Channel Matching OK or Time Scan #Input Guide Channel Number Access Guide Channel SET ScreenEx. When inputting the Guide Channel number 6 for WNJUInd Input Receiving Channel NumberSET Channel Number Express Timer ProgrammingSET Program Date Band indication TV or Catv Press SP/EP to set the tape speedSet to OFF pg , Or DBS appears underCheck, Cancel And Revise Programs Cancel or Revise aRE-ENGAGE Timer ProgramAuto Timer Select Auto SP EP Timer SET ModeAuto SP→EP Timer Or Time Scan %ÞSET Recording Duration Instant Timer Recording ITREngage ITR Mode Press REC on the front panelBefore performing the following steps Prog REC ModeAutomatic Sat- ellite Program Recording Edit To Or From Another Edit From a Camcorder EditingRecord mode. Refer to camcorders instruction Arrow to Tape DUBScan #to set to on ManualLocate Start Point Insert EditingLocate END Point END Insert Editing Engage Insert EditingStart Editing Start Dubbing Audio DubbingEngage Audio Dubbing END Audio DubbingTurn on the TV Speci AL FeaturesTV Multi-Brand Remote Control SET TV Brand CodeTurn on the Cable BOX EN Special FeaturesCable Box Multi-Brand Remote Control Operate Cable BOXEnter DBS Receiver Brand DBS Receiver Multi-Brand Remote ControlTurn on the DBS Receiver Operate DBS ReceiverPlug in Power Cord Unplug Vcrs PowerSET Remote Control Turn VCR Power onTroubleshooting Cassette gets stuck partwayTimer again RoubleshootingOther Problems When scanning channels, someCan the VCR indefinitely remain in the Record-Pause mode? EN Questions and AnswersCan the VCR indefinitely remain in the still mode? What happens if the tape runs out during recording?Index Express Timer ProgrammingMBR Multi-Brand Remote Code Setting List Of TermsFront View Rear View Remote Control 20C to 60C -4F to140F Video connectors in x 1, OUT xSpeci Fications HOW to Locate Your JVC Service Center For Servicing Only in U.S.AWarranty Only in U.S.A. EN Limited WarrantyHR-S4500U
Top Page Image Contents