JVC HR-S6955EK manual Re-perform the clock and/or timer settings

Page 57

subsidiary information

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

57

RECORDING

1.Recording cannot be started.

2.TV broadcasts cannot be recorded.

3.Tape-to-tape editing is not possible.

4.Camcorder recording is not possible.

5.Uand ,on the display panel won’t stop blinking.

There is no cassette loaded, or the cassette loaded has had its record safety tab removed.

L-1, L-2 or F-1 has been selected as the input mode.

The source (another VCR, camcorder) has not been properly connected.

All necessary power switches have not been turned on.

The input mode is not correct.

The camcorder has not been properly connected.

The input mode is not correct.

The end of the tape was reached during Recording.

Insert a cassette, or using adhesive tape, cover the hole where the tab was removed.

Set to the desired preset.

Confirm that the source is properly connected.

Confirm that all units’ power switches are turned on.

Set the input mode to L-1, L-2 or F-1.

Confirm that the camcorder is properly connected.

Set the input mode to L-1, L-2 or F-1.

The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

TIMER RECORDING

1.Timer recording won’t work.

2.Timer programming is not possible.

3.con the display panel won’t stop blinking.

4.c, Uand ,on the display panel won’t stop blinking.

5.cblinks for 10 seconds and the Timer mode is disengaged.

6.The VIDEO Plus+ system does not timer record properly.

The clock and/or the timer have been set incorrectly.

The timer is not engaged.

Timer recording is in progress.

The timer is engaged but there’s no cassette loaded.

The loaded cassette has had its record safety tab removed.

The end of the tape was reached during timer recording.

chas been pressed when there are no programs in memory, or the timer record information has been pro- grammed incorrectly.

The VCR’s preset positions have been set incorrectly.

Re-perform the clock and/or timer settings.

Press cand confirm that cis displayed on the display panel.

Timer programming can’t be performed while a timer recording is in progress. Wait until it finishes.

Load a cassette with the record safety tab intact.

Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact.

The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

Check the programmed data and re-programme as necessary, then press cagain.

Refer to Guide Program Numbers (pg. 54) and re-perform the procedure.

Image 57
Contents HR-S6955EK Blue to N Neutral or Black Brown to L Live or Red Safety PrecautionsMoisture Condensation On The Safe Use Of Equipment Some Do’s And Don’tsContents Display Remote control Front Panel Diagram KeyGetting Everything Ready Welcome to JVCScart and rf Three-Step Quick Start Auto SetupFinish Off Check the ResultsGo straight to 2000 used as example only Perform Clock Set on Go to StepThree-step quick start Basic Features Load a Video Cassette PlaybackPlay Stop & EjectRewind and Fast Forward Video Heads CleaningAdvanced JOG Dial Playback FeaturesPause During Playback Single Frame MovementSlow Motion Variable Speed SearchHigh Speed Search Choose a Programme RecordingSet the Tape Speed Start RecordingResetting the Counter Display Tape Remaining TimeChange Display Information Recording Resume Function Instant Timer RecordingGet to the Video Plus + Screen Enter the PlusCode NumberPress pyou will see the following TV screen information Return to Normal Screen Engage Timer Mode Express Timer Programming Get to the Programme ScreenEnter Programme Details About 5 seconds, then the normal TV screen appears 24H Express Timer Programming Press c, then press oto disengage the timer mode Check, Cancel & Change ProgrammesBasic features Advanced Features Manual Tracking Picture QualityVideo Stabilizer Or E to set to onPicture Control Super VHS ET S-VHS ET Tape TypeSuper VHS S-VHS, S-VHS ET and VHS Your VCR can record in S-VHS, S-VHS ET or VHSSee ‘Super VHS ET S-VHS ET’ on Recording and Playback Using B.E.S.T Avoiding B.E.S.T. Time DelayTurning B.E.S.T. on or OFF Sound Modes Nicam Stereo and Bilingual BroadcastsSoundtrack Selection Skip Search Begin playback. The display panel tells you how many timerIndex Search Instant ReViewEditing Output SettingFor L-2 Input Input SettingEditing Using Another VCR Your VCR as the Player Editing from a Camcorder On-Screen Display O.S.D Other FunctionsAuto SP aLP Timer Power Save ModeAuto Power Off/3H Auto TimerRepeat Playback Next Function MemoryAUX in or Tape Monitor Connection to a Stereo SystemExit Video Channel Set Mode Access Video Channel ModeVideo Channel Set Set Video ChannelTuner Set Auto Channel SetupButton on the Remote Control to move the highlight bar Manual Channel SetupPress Or E Confir- onwards asChange Station Name To the preset position you want then pressDelete a Channel Confirmation screen appearsButton on the Remote Control until the item you want to Change Station Preset PositionButton to move the station to the new preset position Then pressButton on the Remote Control to move the highlight bar to Fine-Tuning Stored ChannelsTV Station ID Guide Channel that you wish to fine-tune then pressBBC1 BBC2 ITV CH4 CH5 TV Station Channel Number GuideClock Set Setting the ClockOr E. The date Or E. Set the correct yearTo receive the TV station then press Or E Manually Setting Guide Program NumbersQuestion and Answers Uand cremain lit on the display panel. Is there a problem?Can the VCR indefinitely remain in the still mode? Can the VCR indefinitely remain in the Record-Pause mode?Symptom Possible Cause TroubleshootingRe-perform the clock and/or timer settings Other Problems Record a Programme While Watching Another List of TermsHR-S6955EK