JVC HR-S7600EK setup guide Step Auto SET UP, Go to item

Page 8
[MENU] : EXIT
AUTO SET
PLEASE WAIT

8

QUICKSETUPGUIDE(cont.)

STEP

3

AUTO SET UP

SET THE TUNER CHANNELS, CLOCK, GUIDE PROGRAM NUMBERS AND VIDEO CHANNEL*

The Auto Set Up function sets the tuner channels, clock, VIDEO Plus+ assigned Guide Program numbers and the video channel*

automatically the first time the button on the recorder or on the remote is pressed to turn on the recorder after the mains power cord has been plugged into a mains outlet.

*Useful if you have connected the video recorder to your TV via RF connection (pg. 6). Video Channel (RF output channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

Before performing the following procedure, make sure that:

the TV aerial cable is connected to the recorder.

the mains power cord is plugged into the mains outlet.

batteries have been installed in the remote control.

1

1–:–

2

Press

 

 

. If "Auto" appears on the display

panel, press OK or #. "Auto" blinks; do NOT press any button on the recorder or

remote control until the display panel shows either the display as illustrated below in item 2 or "– – :– –". Auto Set Up usually takes about 4 – 12 minutes; the duration varies by area.

If "– –:– –" appears on the display panel,

refer to page 10.

If you have connected the video recorder to your TV via both the provided RF cable and a 21-pin SCART cable (AV connection) or via

the provided RF cable, an S-Video cable and 0 + + + an audio cable (S-VIDEO connection) and if

the TV is turned on and set to its AV mode, the

AUTO SET screen will appear.

BeginningEnd

1

2

3

 

4

5

6

 

7

8

9

3

 

0

 

4

 

 

4

1

 

 

3

2

 

 

 

￿

2

3

If you have connected the video recorder to your TV via the provided RF cable only (RF connection) —

the channel that is shown on the display panel is your Video Channel.

To view picture signals from the video recorder, set your TV to the Video Channel. — Refer to the instructions supplied with your TV set for how to do this.

Go to item 3 .

If you have connected the video recorder to your TV via both the provided RF cable and a 21-pin SCART cable (AV connection), or via the provided RF cable, an S-Video cable and an audio cable (S-VIDEO connection)

you do not need the video channel so you have to set the video channel to off.

Press TV PROG – until the display panel shows "_OUT– –" to set the Video Channel to off.

To view picture signals from the video recorder, set your TV to its AV mode.

Refer to the instructions supplied with your TV set for how to do this. Go to item 3 .

Press OK to finish Auto Set Up and refer to page 10 to check the results.

ATTENTION

Once you have performed Auto Set Up, all the stored stations, Guide Program numbers and the video channel remain in the recorder's memory and the recorder will not perform Auto Set Up again. If there is a power cut and the recorder's memory backup expires you only need to reset the clock. (pg. 53)

If you have moved to a different area, perform each setting as required.

Video Channel setting (for RF connection users) pg. 44

Tuner setting pg. 46

Clock setting pg. 53

If a new station begins broadcasting in your area, perform tuner setting (pg. 46) and, if necessary, video channel setting (pg. 44).

NOTES:

Auto channel set function takes place first; it assigns automatically all receivable stations in your area.

Auto clock set function sets the clock automatically.

During auto channel set, the recorder recognizes each station name of the detected stations and stores them in the recorder's memory, then automatically sets the VIDEO Plus+ assigned Guide Program number for those stations according to the broadcast area.

For RF connection users: The video recorder detects the channels which are not occupied by local stations and selects one channel automatically for your Video Channel that is located in the middle of more than 5 vacant channels.

If there is power cut or if you press or MENU while Auto Set Up is in progress, Auto Set Up will be inter- rupted; be sure to turn off the recorder power once and

press to turn the power back on in order to re-start Auto Set Up.

Image 8
Contents HR-S7600EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Some Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Back of RecorderBack of TV Audio in connectors Mains outlet Mains Power CordStep Auto SET UP Go to itemRemote control while downloading is 10 or If -- appears on the display panel, referLink screen will appear. Then the Guide Program number setIf auto channel set has succeeded but auto clock set has not TV Auto Power On Link FunctionsTurn on the Recorder NexTView LinkPlayback Load a CassettePoint Start PlaybackSearch Pause During PlaybackActivate HIGH-SPEED Recording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Access Video PLUS+ ScreenAccess Video PLUS+ Program Screen Enter Pluscode NumberTimer Warning PDC RecordingExpress Timer Programming Before performing Express Timer ProgrammingEnter Programme Start Time TimeSET PDC Mode Timer ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHSPlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemOr press Record on the recorder RecordingPlayback Playback Picture Adjustment Adjust Tracking ManuallyManual Tracking Override Automatic TrackingAccess Main Menu Screen Digital TBC/NRDigital 3R Activate Digital TBC/NRLooking For Scene You Want Activate Index SearchSkip Over Unwanted SectionsSelecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection Type of Broadcast On-screen Display Being ReceivedConnector TV Aerial cable Connector Audio in connectorsAutomatic Satellite Programme Recording Satellite Receiver UnitMove the highlight bar pointer to Mode SET by Before performing the following stepsPressing %Þ, then press OK or% Move the highlight bar pointer to AV2 SELECT, bySET Remote Control RE-SUPPLY PowerRemote A/B Code Switching Remote Con- trol FunctionsTV Multi-brand Remote Control Control Your TV Using Additional ButtonsSET TV Brand Code Operate TVTV Prog +/-,NUMBER keys Satellite Receiver Multi- Brand Remote ControlOperate Satellite Receiver Access Main Menu Screen Access Mode SET ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Edit To Or From Another Video Recorder TV Receiver Player Your recorder Recorder AV1 Select Setting AV2 Select SettingAudio Dubbing Access Main Menu Access Mode SETENABLE/DISABLE Other FunctionsPower Save Mode ModeNext Function Memory Auto SP→LP TimerAuto Timer Engage RECORD-PAUSE Mode Resume RecordingRepeat Playback RetakeConnection To Stereo System Audio Cable not provided SpeakerAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelTest Signal With RF ConnectionAuto Channel Set Tuner SetPerform Auto Channel SET Screen preset positions After Scan CompletedIs displayed on the screen For about 5 seconds, aStoring Channels Manually Input ChannelEnter NEW Channel Information Close Confirmation ScreenDelete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Access Manual Switch StationsChannel SET Screen Select NEW StationTV Station And ID List TV Station Channel Number Guide Channel IslandsClock Set Just ClockGuide Program Number Set Video Plus+ SetupNumber Questions And Answers PlaybackTroubleshooting Won’t stop Blinking To record the entire programmeIndex Front ViewRear View @ #Remote Control Remote Control LCD How To UseEMO Memo Maximum recording time DA4 Double Azimuth helicalVHF 44.5 143/143 470 MHz S7600EK