JVC HR-S7700EU, HR-S7722EU, HR-S7711EU 12 EN, Perform Preset Download, Set the video channel

Page 12

12 EN

INITIAL SETTINGS (cont.)

Preset Download

Auto Channel Set by Downloading from TV/Auto Clock Set/Auto Guide Program Number Set

ATTENTION

You can use this function only with a TV offering T-V Link, etc.* Be sure to use a fully-wired 21-pin SCART cable.

*Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully- wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

If you have connected the recorder to your TV via the AV connection ( pg. 8), the recorder will automatically perform Preset Download instead of the Auto Set Up in step 4 on page

11.After downloading, the recorder sets the clock and Guide Program numbers automatically.

Perform steps 1 to 3 of “Auto Set Up” on page 10 before continuing.

A Perform Preset Download.

Press OK. The AUTO SET/T-V LINK display appears on the front display panel and/or on the TV screen.

On the front display panel

Press rt to select “CH – –” and press OK or e.

On the on-screen display

Press rt to move the highlight bar (pointer) to “T-V LINK” and press OK or

e.

Preset positions on the front display panel increase from “CH1”; do NOT press any button on the recorder or remote control until the front display panel shows clock time, “(CH) 1” or “– –:– –” as illustrated on page 13.

●If you are using the on-screen display, the T-V LINK screen

will appear. Then the GUIDE PROG SET screen will appear during Guide Program Number Set. When Preset Download is completed, “COMPLETED” appears for about 5 seconds, then the normal screen appears.

●If you press any button on the recorder or remote control while downloading is in

progress, it will be interrupted.

NOTES:

●For details, refer to the instruction manual of your TV.

●In the area where no TV station transmits a PDC (Programme Delivery Control) signal, the recorder can perform neither Auto Clock Set nor Auto Guide Program Number Set.

●If there is a power cut, or if you press 1 or MENU while downloading or set up is in progress, it will be interrupted; be sure to turn off the recorder power once and try again from the beginning.

●Auto Clock Set may not function properly depending on the reception condition.

●On this recorder, the characters available for station names (ID) are A–Z, 0–9, –, f, + and I (space). Some names of

downloaded stations may differ from those of your TV ( pg. 56).

B Set the video channel.

Set the video channel to off manually. ( pg. 58)

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Video Cassette Recorder Safety Precautions For Italy Moisture CondensationFront View Front Display Panel ON-SCREEN Display How To Use Operating JVC TVsCheck the contents Situate the recorderConnect the recorder to TV Connect the recorder to mains8To connect to a TV with S-VIDEO/AUDIO in connectors Plug the end of the mains power cord into a mains outletVideo Connection Auto Set Up 10 ENTurn on the recorder Select your countryPerform Auto Set Up Select the languagePress rt to select your language code Press rt to select Auto and press OK or ePerform Preset Download 12 ENSet the video channel Press rt to select CH - and press OK or eLanguage for the on-screen display Just ClockAccess the Main Menu screen Access the Country Set screenLanguage 14 ENInstalling Satellite Controller Situate the Satellite ControllerAttach the Satellite Controller Make connectionsSetting satellite receivers brand and channel 16 ENTV Auto Power On NexTView LinkVCR Auto Standby Direct Rec Basic Playback 18 ENSlow Motion Variable Speed SearchPause during playback Activate frame-by-frame playback20 EN Skip SearchHigh-Speed Turbo Search Instant ReViewIndex Search Next Function MemoryManual Tracking Digital TBC/NR22 EN Repeat PlaybackSoundtrack Selection Activate Repeat PlaybackRecording Resume Function Choose a programmeSet the tape speed Start recordingInstant Timer Recording ITR Engage the ITR mode24 EN Watching AnotherReset the counter Engage the S-VHS ET modeTape Remaining Time Set the counter display26 EN RetakeReceiving Stereo and Bilingual Programmes Playback RecordingAccess the Showview screen Access the Showview Program screenBefore performing the Showview Timer Programming 28 ENSet the VPS/PDC mode Engage the recorder’s timer modeSatellite Receiver Users Guide Program Number SetExpress Timer Programming 30 ENTo Timer-Record Weekly Or Daily Serials VPS/PDC RecordingEnter the channel position Press PR+32 EN Cancel or change programme setting Confirm the overlapping programmesSelect the programme to modify Overlapping programmes blink on the TV screenSelect the L-2 Select mode Recording modeProgramme Recording 34 ENSet the recorder’s input mode Set the edit modeEdit From a Camcorder Start the camcorder1 Output 1 InputPress rt to move Decoder connector 2 Select2 Input Another Video Recorder 38 ENYour recorder Recorder Audio Dubbing 40 ENEngage the Audio Dubbing mode Start dubbingEnd Audio Dubbing Press AUX Number key 0 and/or PR to select F-1 or S-1Insert Editing 42 ENEngage the Insert Editing mode AV Insert EditingLocate the end point Start EditingConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Select the input mode 46 ENConnect the decoder Set the tunerConnecting/Using a Stereo System Make connectionsMode Set Access the Mode Set screenSelect the mode Select the mode settingAuto Timer Picture ControlDirect REC Auto Splp Timer Power Save50 EN Digital 3RVHS Colour SystemAbout Ntsc Playback Access the Auto Channel Set screen Tuner Set52 EN Auto Channel SetPerform Auto Channel Set View the Confirmation screenPress OK twice 54 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a Channel56 EN Set Stations aSet Stations B TV Station And ID List Station NameAccess the Video Channel Set mode Exit the Video Channel Set modeVideo Channel Set 58 ENShowview Setup Guide Program Number SetGuide Program Number Enter the Guide Program numberAccess the Clock Set screen Clock Set60 EN Set the date and time Set Just ClockSet the source channel position for clock data Start the clock operationTroubleshooting 62 ENRecording Other Problems 64 ENPlayback TUNER/TIMER Accessories66 EN GeneralAudio Dubbing Auto Channel Set Auto Set Up Preset Download Delete a ChannelTape Position Indicator Tape Remaining Time Timer Warning Display Tuner SetBefore YOU Start Please Make Sure That International telephone Language codeCountry code
Top Page Image Contents