JVC HR-S8500E/EH Connection To a Satellite Tuner, Satellite Tuner Unit, AV2 IN/DECODER, Switch

Page 46

46ENSYSTEMCONNECTIONS

Connection To A Satellite Tuner

The AV2 IN/DECODER connector on the rear panel of your recorder allows simple connection to a satellite tuner.

Outdoor Unit

Aerial	Aerial connector

Satellite Cable

Satellite Tuner Unit

TV Aerial cable

Back of TV

21-pin AV input connector (SCART)

DECODER

VCR

TV

ANT. IN

EXT.2EXT.1

RF OUT

Mains outlet

IN OUT

S VIDEO

Back of Recorder

AV1 OUT switch

AV1 OUT

COMP. Y/C

		ANT. IN
AV1 IN/OUT	R	L
	AUDIO	OUT
		RF OUT
AV2 IN/DECODER
	PAUSE/
	R.A. EDIT

IMPORTANT

Set "AV2 SELECT" to "SAT" on the Mode Set screen (☞ pg. 39).

If you set "AV2 SELECT" to "SAT"...

●It is possible to view a satellite programme with the TV set to its AV mode even if the recorder's power is turned off.

●The AV2 IN/DECODER connector's input is the same signal that is controlled by the rear panel AV1 OUT switch as shown below: a- If both the satellite tuner and the TV are compatible with the Y/C signal, set the AV1 OUT switch to Y/C in order to take

advantage of high-quality S-VHS pictures. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

b- If the satellite tuner and/or the TV are/is not compatible with the Y/C signal, set the AV1 OUT switch to COMP.

	AV2 SELECT setting on	Rear panel AV1 OUT	AV2 IN/DECODER
	the MODE SET screen	switch	connector input signal

	SAT	COMP.	Composite signal*

		Y/C	Y/C signal**
		Y/C	Y/C signal**

*The composite signal is a regular video signal.

**The Y/C signal is a signal in which the luminance and chrominance signals are separated.

NOTE:

Refer to the instructions supplied with your satellite tuner.

Image 46

Contents HR-S8500E/EH Safety Precautions For Italy Do not place the recorderSituate Recorder Check ContentsBasic Connections Connect Recorder to MainsConnect Recorder to TV Video ConnectionBack of Recorder If you are referring to the front display panel Auto Set UpIf you are referring to the on-screen display Via the provided RF cable only RF connection Supplied with your TV set for how to do thisLanguage Code Your Video ChannelJust Clock If both auto channel set and auto clock set have failedLanguage for the on-screen display Just Clock onLanguage On-Screen Displays Power Save Mode About Ntsc Playback Colour System SetOK or% Point Basic PlaybackLoad a Cassette Start PlaybackStill Picture/Frame-By-Frame Playback Playback FeaturesPlayback Slow MotionManually Adjust TrackingActivate HIGH-SPEED Search Return to AutomaticDigital 3R Digital TBC/NRSoundtrack Selection Activate SpatializerSpatializer During PlaybackTimeScan Audio signal during TimeScanTime JOG & Scan Indicator Variable-Speed SearchTimeScan Audio TimeScanSpeed SP Speed LP Audio output Basic Recording Select Channel to Watch Recording FeaturesEngage ITR Mode SET Recording DurationResume Recording ModeLocate Start Point RetakeReceiving Stereo And Bilingual Programmes Adjust AudioHi-Fi Audio Recording Level Control To Record Stereo And Bilingual Programmes A2Preparation S.T. Picture SystemHighlight bar pointer to MODE%SET, then press Or press Record on the recorder RecordingPlayback During B.E.S.TTimer Programming Timer Warning Satellite Tuner UsersStart Time Express Timer ProgrammingBefore performing Express Timer Programming TimeEngage RECORDER’S SET VPS/PDC ModeTimer Mode VPS/PDC RecordingTime you press Check, Cancel And Replace ProgrammesPress Again to check More information. Each Next programmes Information appearsAuto SP→LP Timer Auto TimerAutomatic Satellite Programme Recording Prog REC ModeBefore performing the following steps SET Remote Control Code Remote Control FunctionsRemove Power Supply RE-SUPPLY PowerSET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons Operate TVBrand Code Satellite Tuner Multi-Brand Remote ControlSET Satellite Tuner Operate Satellite TunerReturn to Normal Screen Editing Mode SettingPreparation For Editing Advantages Of S-VHS Video RecordersEdit From Camcorder If the camcorder has no S-VIDEO output connector RecorderIf the camcorder has an S-VIDEO output connector Recorder PlayerEdit To Or From Another Video Recorder Input ModeSET Edit Mode Make ConnectionsRecorder Player AV2 Select SettingHR-S8500EHR-S8500EH Insert Editing SET Input ModeReset the Counter Locate END PointStart Editing END Insert EditingRandom Assemble Editing Start R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point END R.A. EditEngage Audio Dubbing Audio DubbingAudio OUT Start Dubbing END Audio DubbingSatellite Tuner Unit SwitchConnection To a Satellite Tuner AV2 IN/DECODERConnect Decoder Connecting Using a DecoderSelect Input Mode SET TunerAudio Cable not provided Speaker Connecting Using a Stereo SystemRear View Video Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelTuner Set Auto Channel SetPerform Auto Channel SET View Confirmation ScreenEnter NEW Channel Information Storing Channels ManuallyDelete a Channel When Receiving a Scrambled BroadcastChange Station Channel Position Channel SET Screen Access ManualSwitch Stations Select NEW StationTV Station And ID List Station NameSelect Channel to FINE-TUNE Perform TuningFine-Tuning Channels Already Stored Press OK twice. The Manual Channel Set screen appearsEnter Receiving Channel Position Number Showview SetupNumber Guide Program Number SetClock Set Access Initial SET ScreenAccess Clock SET Screen SET Date and TimeSET Clock Data Source Channel Position SET Just ClockStart Clock Operation Mains power cord is disconnected No power is applied to the recorderRemote control wont function If you’re using the RF OUT connec- tionTimer Recording EN Questions and Answers Ä remain lit on the display panel. Is there Problem?Open the lid to access covered buttons/connectors IndexEN Index Remote Control Specifications Maximum recording timeMemo International Telephone Language Code HR-S8500E/EHEx. Francais is selected for Belgium For More Information see INSTRUCTIONS/P6