JVC HR-S8500E/EH Basic Playback, Load a Cassette, Point, Start Playback, Stop Playback

Page 13

PLAYBACK

EN13

Basic

Playback

Turn on the TV and select the VIDEO channel (or AV mode).

PLAY

8

6	5/8
STOP/EJECTq	1 Á

The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.

LOAD A CASSETTE

Make sure the window side is up, the rear label side is

facing you and the arrow on the front of the cassette is

1 point toward the recorder. Don’t apply too much

pressure when inserting.

● The recorder power comes on automatically and the

counter is reset to 0:00:00.

● If the record safety tab has been removed, playback

begins automatically.

FIND PROGRAMME START

POINT

REW

X 0

FF	SCAN SHUTTLE
	TIME

4

2	If the tape is advanced past the start point, press REW or
		turn the TIME SCAN SHUTTLE ring to the left.
		To go forward, press FF or turn the TIME SCAN
		SHUTTLE ring to the right.

		START PLAYBACK
	Press PLAY. “BEST” appears blinking in the recorder's
3 display panel during automatic tracking. (☞ pg. 24)
		STOP PLAYBACK

LAY1

FF

REW

Press STOP on the remote or STOP/EJECT on the

recorder’s front panel. Then press STOP/EJECT to

4 remove the cassette.

3

STOP

T

V

–

TV PROG –

+

TV

Tape Position Indicator

Usable cassettes

The tape position indicator appears on screen when, from the Stop mode, you press FF, REW or perform an Index Search. The position of “5” in relation to “0”

(beginning) or “+” (end) 0 + shows you where you are

on the tape.

”O.S.D.” (☞ pg. 10) must

be set to “ON”, or the Beginning indicator will not appear.

3

+ +

1:23:45 REMAIN 2:35

End

● Compact VHS camcorder recordings can be played on

this video recorder. Simply place the recorded cassette

into a VHS Cassette Adapter and it can be used just like

any full-sized VHS cassette.

● This video recorder can record on regular VHS and

NOTE:

Depending on the type of tape used, there may be times when the indication is not correct.

Super VHS cassettes. While only VHS signals can be

recorded on regular VHS cassettes, both VHS and Super

VHS signals can be recorded and played back using

Super VHS cassettes.

Image 13

Contents HR-S8500E/EH Safety Precautions Do not place the recorder For ItalyBasic Connections Check ContentsSituate Recorder Connect Recorder to MainsConnect Recorder to TV Video ConnectionBack of Recorder If you are referring to the front display panel Auto Set UpIf you are referring to the on-screen display Language Code Supplied with your TV set for how to do thisVia the provided RF cable only RF connection Your Video ChannelLanguage for the on-screen display If both auto channel set and auto clock set have failedJust Clock Just Clock onLanguage On-Screen Displays Power Save Mode About Ntsc Playback Colour System SetOK or% Load a Cassette Basic PlaybackPoint Start PlaybackPlayback Playback FeaturesStill Picture/Frame-By-Frame Playback Slow MotionActivate HIGH-SPEED Search Adjust TrackingManually Return to AutomaticDigital TBC/NR Digital 3RSpatializer Activate SpatializerSoundtrack Selection During PlaybackTime JOG & Scan Indicator Audio signal during TimeScanTimeScan Variable-Speed SearchTimeScan Audio TimeScanSpeed SP Speed LP Audio output Basic Recording Engage ITR Mode Recording FeaturesSelect Channel to Watch SET Recording DurationLocate Start Point ModeResume Recording RetakeHi-Fi Audio Recording Level Control Adjust AudioReceiving Stereo And Bilingual Programmes To Record Stereo And Bilingual Programmes A2Preparation S.T. Picture SystemHighlight bar pointer to MODE%SET, then press Playback RecordingOr press Record on the recorder During B.E.S.TTimer Programming Satellite Tuner Users Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingStart Time TimeTimer Mode SET VPS/PDC ModeEngage RECORDER’S VPS/PDC RecordingPress Again to check More information. Each Check, Cancel And Replace ProgrammesTime you press Next programmes Information appearsAuto Timer Auto SP→LP TimerAutomatic Satellite Programme Recording Prog REC ModeBefore performing the following steps Remove Power Supply Remote Control FunctionsSET Remote Control Code RE-SUPPLY PowerControl Your TV Using Additional Buttons TV Multi-brand Remote ControlSET TV Brand Code Operate TVSET Satellite Tuner Satellite Tuner Multi-Brand Remote ControlBrand Code Operate Satellite TunerPreparation For Editing Editing Mode SettingReturn to Normal Screen Advantages Of S-VHS Video RecordersIf the camcorder has an S-VIDEO output connector Recorder If the camcorder has no S-VIDEO output connector RecorderEdit From Camcorder PlayerSET Edit Mode Input ModeEdit To Or From Another Video Recorder Make ConnectionsRecorder Player AV2 Select SettingHR-S8500EHR-S8500EH Reset the Counter SET Input ModeInsert Editing Locate END PointEND Insert Editing Start EditingRandom Assemble Editing Locate EDIT-OUT Point Locate EDIT-IN PointStart R.A. Edit END R.A. EditEngage Audio Dubbing Audio DubbingAudio OUT END Audio Dubbing Start DubbingConnection To a Satellite Tuner SwitchSatellite Tuner Unit AV2 IN/DECODERSelect Input Mode Connecting Using a DecoderConnect Decoder SET TunerAudio Cable not provided Speaker Connecting Using a Stereo SystemRear View Exit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelAuto Channel Set Tuner SetView Confirmation Screen Perform Auto Channel SETStoring Channels Manually Enter NEW Channel InformationDelete a Channel When Receiving a Scrambled BroadcastChange Station Channel Position Switch Stations Access ManualChannel SET Screen Select NEW StationStation Name TV Station And ID ListFine-Tuning Channels Already Stored Perform TuningSelect Channel to FINE-TUNE Press OK twice. The Manual Channel Set screen appearsNumber Showview SetupEnter Receiving Channel Position Number Guide Program Number SetAccess Clock SET Screen Access Initial SET ScreenClock Set SET Date and TimeSET Clock Data Source Channel Position SET Just ClockStart Clock Operation Remote control wont function No power is applied to the recorderMains power cord is disconnected If you’re using the RF OUT connec- tionTimer Recording Ä remain lit on the display panel. Is there Problem? EN Questions and AnswersIndex Open the lid to access covered buttons/connectorsEN Index Remote Control Maximum recording time SpecificationsMemo Ex. Francais is selected for Belgium HR-S8500E/EHInternational Telephone Language Code For More Information see INSTRUCTIONS/P6