JVC HR-J255ES, HR-J455EK, HR-J255EK, HR-J256EK setup guide SET Tape Speed, SET PDC Mode

ENTER PRESET POSITION

	Press TV PROG +/– to				– P1 –
	enter the preset position
6 corresponding to the				START		STOP
				21:00	= 22:00
	broadcasting station you			SP	VPS/PDC OFF
	wish to record.
				DATE		TV PROG
				25.12	1
				[+/–] =		BBC 1
				[PROG] : EXIT
		SP
	SET TAPE SPEED
7 Press SP/LP (			) to set the tape speed.
8	SET PDC MODE
	Press PDC to select "ON" or "OFF".
	If "VPS/PDC ON" is displayed on the screen or "VPS/
	PDC" is lit on the display panel, PDC is set to ON.
	If "VPS/PDC OFF" is displayed on the screen or "VPS/
	PDC" is not lit on the display panel, PDC is set to OFF.

☞"PDC Recording" in the right column.

● VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this recorder.

	RETURN TO NORMAL
	SCREEN
	After confirming all information is correct, press PROG
	or OK. "PROGRAM COMPLETED" appears on the
9 screen for about 5 seconds, then normal screen
	appears.
	● Repeat steps 1 – 9 for each additional programme.
	ENGAGE RECORDER’S
10	TIMER MODE
	Press ä. The recorder turns off automatically and ä
	appears on the display panel.
	● To disengage the timer, press ä again.

To Timer-Record Weekly Or Daily Serials . . .

. . . anytime during steps 2 through 9, press WEEKLY (NUMBER key “9”) for weekly serials or DAILY (NUMBER key “8”) for daily serials (Monday – Friday). Either "WEEKLY" or "DAILY" appears on the screen. Pressing the button again makes the corresponding indication disappear.

NOTE:

You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, "PROGRAM FULL" appears on screen and "FULL" appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes (☞ pg. 18).

17

Satellite Receiver Users

To timer-record a satellite broadcast using Express Timer Programming:

1Perform steps 1 – 10. Enter "L-2" for the preset position in step 6.

2Set the satellite receiver to the appropriate channel before the selected programme begins.

3Leave the satellite receiver's power on.

PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times which you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service only in a very few areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your recorder will not start recording if PDC has been selected. Be sure to set PDC to "OFF" if PDC is not available on your selected channel. (☞ step 8 in the left column).

NOTES:

●Set the start time (PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.

●PDC recording is also possible when a satellite receiver or a cable system is connected to AV2 IN on your recorder.

●PDC recording is also possible via the AV1 IN/OUT connector.