JVC HR-J4003UM manual Turn on the TV, SET Remote Control, SET TV Brand Code, Operate TV

Page 31

SPECIALFEATURES

31

TV/VIDEO
	1	2	3
NUMBER	4	5	6
NUMBER
	7	8	9
		0

VOL. +/-

STOP

POWER

ENTER

TV/VCR

TV Multi-Brand Remote Control

The VCR's remote control can control several functions on JVC remote control TVs and on the brands of remote control TVs listed below. Some TV brands have more than one code. If the TV will not function with one code, try entering another.

	TURN ON THE TV
1 Turn the power on using the TV's remote control.
	SET REMOTE CONTROL
2	MODE
	Set the TV/VCR switch on the VCR's remote control to
	TV.
	SET TV BRAND CODE
	Refer to the chart below. While holding down POWER,
	enter your TV’s brand code using the NUMBER keys,
3 then press STOP.
	● Once you have set the remote control to operate the
	TV, you don’t have to repeat this step until you
	replace your remote control’s batteries.

OPERATE TV

4 First, press POWER on the remote to see if the TV’s power goes off as it should. If it does, try other operations.

TV BRAND NAME	BRAND CODE
JVC	01
PHILIPS	03
PHILICO/HITACHI	05
SHARP	06
TOSHIBA	07
MITSUBISHI	08
PHILICO/DAEWOO	09
PACKARD BELL	09
KIOTE/DAEWOO	09
DAEWOO	10
SAMSUNG	11
GOLDSTAR	12
RCA	14
PANASONIC	15, 16
SONY	18
ZONDA	19, 20, 21
AKAWA	21, 22
ELECTRA	23
PHILICO	25

●The POWER, TV/VIDEO, CH5°, VOL +/– and NUMBER keys on the remote can all be used to operate the TV. *For some brands of TV, you must press ENTER after having pressed the NUMBER keys.

●To return the remote to VCR control, set the TV/VCR switch to VCR.

NOTE:

Depending on the kind of TV, there may be cases where some or all functions cannot be operated using the remote control.

Image 31

Contents HR-J4003UM Do not place the VCR This unit is produced to comply with Standard IEC PublContents Basic Connections Clock Make Corrections Access Clock SET ScreenClock Setting SET Date and TimeTuner Access Main MenuAccess Tuner SET Access Band ScreenReturn to Normal Screen Perform Auto Channel SETPress Menu as many times as necessary Channel SET Screen Access Tuner SET ScreenAccess AFC Screen Access ManualStart Playback Simple PlaybackLoad a Cassette Find Program Start PointSimple Recording During Playback PlaybackFRAME-BY-FRAME PlaybackManual Tracking Engage Manual Tracking ModeAdjust Manual Tracking RE-ENGAGE Automatic TrackingAccess Superimpose Access Function SETSuperimpose Stop Repeat Access Distant CodeSkip Over Unwanted Sections Start RepeatReturn to Counter Position Zero Activate Instant ReviewActivate Counter MemoryNext-Function Memory Tape Position IndicatorS.T. Picture System Access Main Menu ScreenSystem Begins with the picture Level optimized RecordingPress and hold REC Quality of the tape Use, then recordingBefore beginning, perform steps 1 and 2 on PlaybackTape in use Select Channel for Viewing Engage TV ModeReset Counter to Zero RecordingAccess Program SET Screen Instant Timer Recording ITROn-Screen Timer Programming Engage ITR ModeSET Program Select Program NumberInformation RE-ENGAGE Timer Disengage TimerAccess Program SET Cancel a ProgramYour choice on or Access Auto SP/EPAuto SP/EP Timer Place the arrow next to Auto SP/EP Timer byAuto Timer Access Auto TimerEdit From a Camcorder Control Two JVC VCRs SET RECORDER’S Input ModeEdit To Or From Another Load CassettesPrepare for Editing Random As- semble EditingStart R.A. Edit Locate EDIT-OUT PointEND R.A. Edit SET TV Brand Code SET Remote ControlTV Multi-Brand Remote Control Turn on the TVCassette gets stuck partway Remote control won’t function Batteries are dischargedMake sure the window side is up, When scanning channels, some Timer againHas not been programmed correctly Cassette is automatically Questions and Answers List Of Terms MBR Multi-Brand Remote Code SettingPower Ramdom Assemble Editing connector pgFront Display Panel Remote Control ProvidedFrequency-synthesized tuner EIA monochrome signal20C to 60C -4F to140F Maximum recording time