JVC HR-J267MS, HR-J261MS Video Channel Set, Access Video Channel SET Mode, Select TV System

Page 4

4ENINITIALSETTINGS

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

If you have connected the video recorder to your TV via the provided RF cable only (RF connection) – Go to "With RF Connection" below.

If you have connected the video recorder to your TV via both the provided RF cable and an AV cable (AV connection) – Go to "With AV Connection" on next page.

With RF Connection

IMPORTANT:

Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder.

TV PROG+/–

STOP/EJECT

1

1 2 3

4 5 6

7 8 9

04

2

TV PROG+/–

3

OK

1

2

ACCESS VIDEO CHANNEL SET MODE

Hold down STOP/EJECT on the recorder until the display panel shows the following.

SELECT TV SYSTEM

Press TV PROG + or – to set appropriate TV system that matches the system of TV being used (refer to the table below).

	1 : B/G 2 : D/K 3 : I	4 : H

	Major Countries	TV System

	New Zealand, Kuwait, U.A.E.,
	Indonesia, Singapore, Thailand,	B/G
	Malaysia, Iran, Saudi Arabia,	B/G
	Malaysia, Iran, Saudi Arabia,
	Egypt, Morocco, Lebanon, Iraq

	China, Mongolia, Russia	D/K

	Hong Kong	I

	Australia	H

TEST SIGNAL

The channel on which the screen to the left appear clearly in step 3 is your Video Channel.

To view picture signals from the video recorder, set your TV to the Video Channel.

Image 4

Contents HR-J267MS HR-J261MS Auto Head Cleaner Safety PrecautionsDo not place the recorder Check Contents Basic ConnectionsSituate Recorder Connect Recorder to MainsAccess Video Channel SET Mode Video Channel SetSelect TV System EN I Nitial Sett IngsSET Video Channel Finish Video Channel SETFinish Video Channel SETAuto Set Up Select LanguageSET Time SET DateDuring Auto Set Up Start Auto Channel SETMajor Countries TV System Press OK or Push JOG ÞAccess Main Menu Screen ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Turn on the RecorderAccess Initial SET Screen Select LanguageClock Set PressPress Menu Press Push JOG %Þto place the pointer next toBasic Playback Load a CassettePoint Start PlaybackPlayback Features SearchPlayback Activate HIGH-SPEED SearchAdjust Tracking Manually Return to Automatic TrackingActivate Instant Review Manual TrackingActivate Index Search Activate Repeat PlaybackEN Playback Index SearchAccess Main Nenu Screen SET ModeTape Position Indicator Picture ControlBasic Recording Recording Features Reset CounterEngage ITR Mode Select Channel to WatchAccess Main Menu Screen S.T. Picture SystemReturn to Normal EN RecordingPlayback RecordingOr press Record on the recorder Express Timer Programming Timer RecordingStart Time Enter Programme DateReturn to Normal Timer ModeEngage Recorders Disengage Timer Mode Cancel or Replace a ProgrammeReturn to Timer Mode Check, Cancel And Replace ProgrammesAuto Timer Auto SP→LP TimerReturn to Normal Screen Edit To Another Video Recorder Edit From a Camcorder Or Another Video Recorder SET Recorders InputMode Source playerSetting Of The Colour System Select Buttons Mode DisplayMode Description Off-Air RecordingTape-To-Tape Editing Recorded tape HR-J267MS/HR-J261MSRecorded tape Playback equipmentMode Select TV SystemTuner SET Auto Channel SetAccess Tuner SET Access Channel ListSelect Position SET Desired StationAccess Channel List EN Tuner SETDelete a Channel Swap Channel PositionsFine-Tuning Channels FINE-TUNETroubleshooting If youre using the RF OUT connec- tionPress Play to turn the indicator off Check the cassette Try manual tracking. pgTimer again RecordingOubleshooting New one. pgQuestions and Answer S E N Playback RecordingIndex Front ViewDisplay Panel Remote Control Prog +/-,TV VOL +/-, TV MutingSpecification S HR-J261MS