JVC InHR-J4404UM manual Plug & Play, Auto Tuner Set, Press Menu as many times as necessary

Page 5

INITIALSETTINGS

5

Plug & Play

Auto Tuner Set

ª £

q

2 5/8 3

IMPORTANT

Don't press any buttons on the VCR or remote while Plug & Play is in progress.

If you perform Plug & Play successfully, there's no need to perform the Tuner procedures (pg. 8). If, however, you want to add or delete channels, refer to "Add Or Delete A Channel" on page 10.

The Plug & Play function sets the tuner channels automatically when the POWER button is first pressed to power on the VCR after you connect the power plug to an AC outlet.

PLUG & PLAY SETUP

1 Connect the antenna cable to the VCR (pg. 4). Then

connect the VCR's power plug to an AC outlet.

TURN ON THE VCR

2 Press POWER. The tuner channels will automatically be set.

The auto channel set function scans all the channels that are receivable by your VCR. It then automatically assigns each receivable channels to the CHbuttons. It skips non-receivable channels. During auto channel set the channel numbers are displayed as they are scanned and set.

After you perform Plug & Play, if the tuner channels have not been set properly or if "SIN SEÑAL" is displayed on screen, make sure that the antenna cable is connected to the VCR properly and turn off the VCR power once, then turn the power back on; the VCR will try Plug & Play again.

RETURN TO NORMAL SCREEN

3 Press MENU as many times as necessary.

AJUSTE AUTOMATICO

AJUSTE AUTOMATICO

DE CANALES

DE CANALES

On-Screen Display

EXPLORANDO ...

FIN DE EXPLORACION

PRESIONE (MENU) P/TERMINAR

PRESIONE (MENU) P/TERMINAR

During Plug & Play

The channel numbers are displayed as they are scanned and set.

When Plug & Play is completed, the lowest position number will appear on the front display panel.

Front Display Panel

Be sure to connect the power plug to an AC outlet first before installing the lithium battery; otherwise, the battery's service life will be drastically shortened.

Installing/Removing the lithium battery

1Make sure that the power plug is connected to an AC outlet and turn off the VCR power.

2Open the battery cover while pressing the release tab as illustrated.

3Insert a lithium battery with the plus (+) side up and push it in.

To remove the lithium battery, press the latch A down- ward using a pointed non-metallic object, then pull out the lithium battery.

4Close the battery cover until it clicks in place.

A

Image 5
Contents HR-J4404UM This unit is produced to comply with Standard IEC Publ Dear CustomerContents Basic Connections Auto Tuner Set Plug & PlayPress Menu as many times as necessary During Plug & PlayClock Clock Setting Access Clock SETSET Date and Time Make CorrectionsAccess Tuner SET Access Main MenuAccess Band Screen TunerReturn to Normal Screen Perform Auto Channel SETAccess Manual Access AFC ScreenMake Selection Channel SET ScreenLoad a Cassette Simple PlaybackFind Program Start Point Start PlaybackSimple Recording Playback Features Adjust Manual Tracking Engage Manual Tracking ModeRE-ENGAGE Automatic Tracking Start RepeatVideo Stabilizer Superimpose Access Function SETAccess Superimpose Start Search Access Distant CodeSkip Over Unwanted Sections Return to Counter Position Zero Activate CounterMemory System Screen S.T. Picture SystemPress and hold REC RecordingQuality of the tape Use, then recording Begins with the picture Level optimizedTape in use PlaybackEngage TV Mode Recording FeaturesReset Counter to Zero Select Channel for ViewingEngage ITR Mode Instant Timer Recording ITRSET Recording Duration Press RECAccess ON-SCREEN Menu On-Screen Timer ProgrammingAccess Program SET Screen InformationPress just once to access the Auto Timer screen Engage Timer ModePress TIMER. The VCR turns off automatically Until the item you want to change begins blinkingAccess Program SET Disengage TimerCancel a Program RE-ENGAGE TimerAccess Function SET Screen Access Main Menu ScreenAuto SP/EP Timer SP modeAccess Auto Timer Screen Access Auto TimerAuto Timer Or Push JOG%ÞEdit To Or From Another SET RECORDER’S Input Edit From a CamcorderMode PlayerTurn on the TV TV Multi-Brand Remote ControlSET TV Brand Code Operate TVTurn on the Cable BOX Cable Box Multi-Brand Remote ControlEnter Cable BOX Brand Operate Cable BOXEx. To set remote control to RCA Satellite Receiver Multi Brand Remote ControlTurn on the Satellite Receiver BrandSET Remote Control Unplug Vcrs PowerPlug in Power Cord Turn VCR Power onQuestions and Answer S Make sure the window side is up, Cassette gets stuck partwayHas not been programmed correctly Cassette is automatically Timer againWhen scanning channels, some Index Rear View How To Use Remote Control ProvidedInstalling Batteries Do not block the VCR’s ventilation openings Do not place the VCRDo not place heavy objects on the VCR or remote ControlEMO Memo HR-J4404UM