JVC HR-VP782U 18 EN, Connect DBS receiver to VCR, How to control the DBS receiver, Controller

Page 18

18 EN

INITIAL SETTINGS (cont.)

DBS Receiver Control Setting

Suggested location

Place the DBS (Direct Broadcast Satellite) receiver on top of the VCR. Attach the VCR’s Controller to the top of the VCR with the Controller’s transmitter pointed towards the DBS receiver’s remote sensor.

ATTENTION:

The Controller can also control a cable box. If both a DBS receiver and a cable box are used, position the Controller so its signal reaches the remote sensors on both the DBS receiver and cable box.

DBS receiver

Controller

Your VCR(suggested

locations)

DBS receiver

Controller

 

(not supplied)

 

To

To

RF output

Audio/Video

Transmitter

output

or

 

To

To

AUDIO/

ANT. IN

VIDEO IN

 

Your VCR

CABLE

BOX

The following procedure is required if you receive satellite channels through a DBS (Direct Broadcast Satellite) receiver. The Controller allows the VCR to automatically switch the DBS receiver’s channels during timer recording.

NOTES:

The Controller is not supplied with this unit. It can be requested by mailing in the completed JVC Cable Mouse Certificate that is included with the accessory package. The VCR can automatically change the DBS receiver channels using the Controller when the VCR has been programed using Express timer programing ( pg. 34). Because satellite programing does not use PlusCode, the Controller cannot change the DBS receiver channels during VCR Plus+ timer recording.

If a cable box is also used, it is recommended that you connect the DBS receiver to your VCR’s audio/video input connectors and the cable box to your VCR’s antenna input terminal.

Installing Controller

1 Situate Controller

Place the Controller so that its transmitter is facing the DBS receiver’s remote sensor.

Make sure the path between the Controller and the DBS receiver’s remote sensor is not blocked.

2 Attach Controller

Fix securely using the adhesive strip attached on the back of the Controller.

3 Connect DBS receiver to VCR

If your DBS receiver does not have audio/ video input connectors

Connect the RF output terminal on the DBS receiver to the ANT. IN terminal on the rear of your VCR.

If your DBS receiver has audio/video input connectors

Connect an audio/video cable between the AUDIO/VIDEO IN connectors on the rear of the VCR and the audio/video output connectors on the DBS receiver.

NOTE:

When connecting your DBS receiver, refer to its instruction manual.

4 Connect Controller to VCR Connect the Controller to the CABLE BOX Controller connector on the rear panel.

How to control the DBS receiver

This VCR has two separate methods to control your DBS receiver.

The VCR’s wireless Remote can control your DBS receiver. This eliminates the need for a separate DBS receiver’s Remote. The VCR’s Controller can also control your DBS receiver. This allows the VCR to change your DBS receiver’s channel number during timer-recording.

Each method must be set up separately. To set up the VCR’s Remote, refer to page 48. To set up the Controller, go to page 19.

Page 17 Page 19
Image 18
Page 17 Page 19
Contents HR-VP782U Dear Customer Telephone NumberPower Cord Protection Power SourcesPower Lines Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsContents Antenna or cable Audio OUT not supplied AC Power CordBasic Connections Coaxial cableConnect VCR to TV Check contentsSituate VCR Final preparation for useWhat to do if Plug & Play setting failed Plug & Play SettingPerform Plug & Play setup Clock and tuner channels will be set automaticallySelect language Language SettingAccess Initial Set screen Return to normal screenClock Setting 10 ENPreparations Select host channel Setting clock semiautomaticallySet Auto Clock to on Select time zone12 EN Setting clock manuallySelect D.S.T. mode Manual Clock SetTuner Setting Access Tuner Set screenPerform Auto Channel Set 14 EN Setting channels manuallyAccess Manual Channel Set screen Add or skip desired channelsAttach Controller Cable Box Control SettingSituate Controller Connect cable box to VCR16 EN Access Main Menu screen on VCRAccess Cable Box Set screen Turn on cable boxAccessPress OKCable. Box Brand Set screen Enter cable box brandIf the cable boxs channel does not change to Connect DBS receiver to VCR How to control the DBS receiver18 EN ControllerAccess DBS Receiver Set screen Turn on DBS receiverSelect DBS receiver output channel Access DBS Receiver Brand Set screen 20 ENEnter DBS Receiver’s brand Basic Playback Load a cassetteStart playback Changing display information Basic Playback Features22 EN Checking tape positionAdjusting tracking condition Selecting monitor soundAutomatic operations after 24 EN Locating beginning of timerAccess distant code Locating beginningSelect recording channel BasicRecording Set tape speedSpecifying recording length Basic Recording Features26 EN Watching one program while recording anotherErase on-screen display Showing on-screen displayDisplay VCR status on TV screen Accidental erasure preventionLocating particular scene Special Effect Playback28 EN Rapidly Picture Search High-Speed Picture SearchViewing slow motion picture Viewing still pictureSkipping unwanted portions Pause during playbackVCR Plus+ Timer Programing 30 ENInput receiving channel number Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Press SP/EPVCR Plus+ Setup 32 ENVCR Plus+ guide channel matching Access Guide Channel Set screen Input guide channel numberExpress Timer Programing 34 ENTo timer-record daily Monday-Friday or weekly serials Checking program settings 36 ENConfirm overlapping programs Select program to modifyOverlapping programs blink on the screen 38 EN Useful Function SettingsChange setting Select FunctionWhen this function is set to on When this function is set to OFF40 EN For ExampleThis VCR Preventing 42 ENEdit To Or From Another ConnectionThis VCR for recording Edit From Camcorder44 EN Camcorder for playbackEnable remote pause function Select input mode on this VCRAccess Main Menu screen on this VCR Select Edit for Picture ControlTurn on the TV TV Brand Setting46 EN Set TV brand codeEnter cable box brand code Cable Box Brand SettingTurn on the cable box Operate cable boxTurn on the DBS receiver DBS Receiver Brand Setting48 EN Enter DBS receiver brand codeUnplug VCR Changing Remote Control CodeSet remote control code for Remote Plug in VCRTroubleshooting 50 ENTimer Recording Other Problems 52 ENCan the VCR indefinitely remain in still mode? What happens if the tape reaches its end during recording?54 EN List of termsFront panel Front display panel56 EN Rear panelOn-screen display How to use the Remote RemoteFull-Size VHS 30 ST-30 58 ENUsable cassettes Compact VHS* TC-20 ST-C20 TC-30 ST-C30 TC-40 ST-C40HOW to Locate Your JVC Service Center Limited Warranty 60 ENMemo 62 EN Page HR-VP782U
Top Page Image Contents