JVC HR-VP782U manual TV Brand Setting, 46 EN, Turn on the TV, Set TV brand code, Operate TV

Page 46

46 EN

MULTI-BRAND REMOTE CONTROL

TV Brand

Setting

This Remote can control some functions of remote controllable TVs listed below. Without setting, you can control a JVC TV.

1 Turn on the TV

Turn on the TV using the Power button on the TV or its Remote.

2–14

TV

TV/VCR 1

4

7

			2–2
			POWER
2	3
5	6	2	2–3
8	9		Number
0		4

2Set TV brand code

Follow the example shown below.

1Press and hold TV.

2 Press MBR SET.

3 Press the Number keys to enter your TV’s brand code by referring to the table below.

4 Press OK, and release TV.

The TV should turn off. If it does, try other

operations below. ( step 3).

Once you have set the Remote to operate the TV, you do not have to set it until you replace the batteries from the Remote.

PANASONIC has two codes. If the TV does not function with one code, try entering the other.

1

3

2–4

ENTER

TV VOL +/–

TV CH +/–

3Operate TV

While holding down TV, press one of the following buttons: POWER, TV/VCR, TV CH +/–,

TV/VCR, (TV Muting), TV VOL +/–, and Number keys.

For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

NOTES:

Depending on the type of TV, some or all functions cannot be operated using this Remote.

It’s not possible to operate a TV not equipped with a remote sensor.

TV BRAND NAME	BRAND CODE
JVC	01, 03
HITACHI	10
MAGNAVOX	02
MITSUBISHI	03
PANASONIC	04, 11
RCA	05
SHARP	06
SONY	07
SAMSUNG	12
SANYO	13
SEARS	13
TOSHIBA	08
ZENITH	09

(Ex.) To set Remote to RCA 05:

	MBR SET
TV	A/B		ENTER/O
	0	5		SD
	0	5	3	OK

Hold	Press in succession
down

Release

Image 46

Contents HR-VP782U Dear Customer Telephone NumberPower Cord Protection Power SourcesPower Lines Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsContents Antenna or cable Audio OUT not supplied AC Power CordBasic Connections Coaxial cableConnect VCR to TV Check contentsSituate VCR Final preparation for useWhat to do if Plug & Play setting failed Plug & Play SettingPerform Plug & Play setup Clock and tuner channels will be set automaticallySelect language Language SettingAccess Initial Set screen Return to normal screen10 EN Clock SettingPreparations Select host channel Setting clock semiautomaticallySet Auto Clock to on Select time zone12 EN Setting clock manuallySelect D.S.T. mode Manual Clock SetAccess Tuner Set screen Tuner SettingPerform Auto Channel Set 14 EN Setting channels manuallyAccess Manual Channel Set screen Add or skip desired channelsAttach Controller Cable Box Control SettingSituate Controller Connect cable box to VCR16 EN Access Main Menu screen on VCRAccess Cable Box Set screen Turn on cable boxEnter cable box brand AccessPress OKCable. Box Brand Set screenIf the cable boxs channel does not change to Connect DBS receiver to VCR How to control the DBS receiver18 EN ControllerTurn on DBS receiver Access DBS Receiver Set screenSelect DBS receiver output channel 20 EN Access DBS Receiver Brand Set screenEnter DBS Receiver’s brand Load a cassette Basic PlaybackStart playback Changing display information Basic Playback Features22 EN Checking tape positionSelecting monitor sound Adjusting tracking conditionAutomatic operations after 24 EN Locating beginning of timerAccess distant code Locating beginningSelect recording channel BasicRecording Set tape speedSpecifying recording length Basic Recording Features26 EN Watching one program while recording anotherErase on-screen display Showing on-screen displayDisplay VCR status on TV screen Accidental erasure preventionLocating particular scene Special Effect Playback28 EN Rapidly Picture Search High-Speed Picture SearchViewing slow motion picture Viewing still pictureSkipping unwanted portions Pause during playbackVCR Plus+ Timer Programing 30 ENInput receiving channel number Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Press SP/EP32 EN VCR Plus+ SetupVCR Plus+ guide channel matching Access Guide Channel Set screen Input guide channel numberExpress Timer Programing 34 ENTo timer-record daily Monday-Friday or weekly serials Checking program settings 36 ENSelect program to modify Confirm overlapping programsOverlapping programs blink on the screen 38 EN Useful Function SettingsChange setting Select FunctionWhen this function is set to on When this function is set to OFF40 EN For ExampleThis VCR Preventing 42 ENEdit To Or From Another ConnectionThis VCR for recording Edit From Camcorder44 EN Camcorder for playbackEnable remote pause function Select input mode on this VCRAccess Main Menu screen on this VCR Select Edit for Picture ControlTurn on the TV TV Brand Setting46 EN Set TV brand codeEnter cable box brand code Cable Box Brand SettingTurn on the cable box Operate cable boxTurn on the DBS receiver DBS Receiver Brand Setting48 EN Enter DBS receiver brand codeUnplug VCR Changing Remote Control CodeSet remote control code for Remote Plug in VCRTroubleshooting 50 ENTimer Recording Other Problems 52 ENCan the VCR indefinitely remain in still mode? What happens if the tape reaches its end during recording?54 EN List of termsFront panel Front display panelRear panel 56 ENOn-screen display How to use the Remote RemoteFull-Size VHS 30 ST-30 58 ENUsable cassettes Compact VHS* TC-20 ST-C20 TC-30 ST-C30 TC-40 ST-C40HOW to Locate Your JVC Service Center Limited Warranty 60 ENMemo 62 EN Page HR-VP782U