JVC HR-VP782U manual 20 EN, Access DBS Receiver Brand Set screen, Enter DBS Receiver’s brand

Page 20

DBS RECEIVER BRAND SET

51

DID YOUR DBS RECEIVER CHANGE TO CHANNEL 100? =YES

NO

PRESS (5,°), THEN (OK)

PRESS (MENU) TO END

DBS RECEIVER BRAND SET

4 0

PRESS NUMBER KEY (0–9)

THEN (OK) TO TEST PRESS (MENU) TO END

20 EN

INITIAL SETTINGS (cont.)

6

6

					7
				REW	FF
				PLAY
POWER
MENU
VIDEO (MONO)L—AUDIO—R
OK	SP	EP	CH
OK		VCR	CH	REC	STOP/EJECT PAUSE

SP/EP

1 2 3

4 5 6 2 7

7 8 9

0 4

1

67

Access DBS Receiver Brand Set screen

Press OK.

Enter DBS Receiver’s brand

On the Remote ONLY:

Press the appropriate Number keys to enter the brand code from the following list, then press OK.

The program currently received through the

DBS receiver appears for about 10 seconds.

BRAND	CODE
JVC (DISH Network)	51
ECHOSTAR (DISH Network)	51
PRIMESTAR	50
SONY (DSS)	41
RCA (DSS)	40

If the DBS receiver’s channel changes to the channel listed below for your brand, setting is complete

JVC = 100 ECHOSTAR = 100 PRIMESTAR = 55 SONY = 205 RCA = 205

Press OK and “DBS

RECEIVER CONTROL IS ON” appears on the screen for about 5 seconds, then it returns to the normal screen.

If the DBS receiver’s channel does not change as shown above

1Press SHUTTLE PLUS %Þ (or CH 5° on the front panel) to move the highlight bar (arrow) to “NO”.

2Press OK.

3Re-enter the correct code.

NOTES:

The Controller may not work with all types of DBS receiver. If your DBS receiver does not respond to the code, you cannot use the Controller to change satellite channels. In this case, make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start time of timer recording.

The VCR can only change the satellite channel through the Controller during timer recording.

If your DBS receiver cannot be operated with a remote control (because it has no remote sensor), you cannot use the Controller to change its channels. Make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start time of timer recording.

For customers in U.S.A.: If you are unable to set the Controller, contact JVC toll free at 1-800-252-5722.

Image 20

Contents HR-VP782U Dear Customer Telephone NumberPower Sources Power LinesPower Cord Protection Grounding or PolarizationAccessories Damage Requiring ServiceCleaning Replacement PartsContents Audio OUT not supplied AC Power Cord Basic ConnectionsAntenna or cable Coaxial cableCheck contents Situate VCRConnect VCR to TV Final preparation for usePlug & Play Setting Perform Plug & Play setupWhat to do if Plug & Play setting failed Clock and tuner channels will be set automaticallyLanguage Setting Access Initial Set screenSelect language Return to normal screenPreparations Clock Setting10 EN Setting clock semiautomatically Set Auto Clock to onSelect host channel Select time zoneSetting clock manually Select D.S.T. mode12 EN Manual Clock SetPerform Auto Channel Set Tuner SettingAccess Tuner Set screen Setting channels manually Access Manual Channel Set screen14 EN Add or skip desired channelsCable Box Control Setting Situate ControllerAttach Controller Connect cable box to VCRAccess Main Menu screen on VCR Access Cable Box Set screen16 EN Turn on cable boxIf the cable boxs channel does not change to AccessPress OKCable. Box Brand Set screenEnter cable box brand How to control the DBS receiver 18 ENConnect DBS receiver to VCR ControllerSelect DBS receiver output channel Access DBS Receiver Set screenTurn on DBS receiver Enter DBS Receiver’s brand Access DBS Receiver Brand Set screen20 EN Start playback Basic PlaybackLoad a cassette Basic Playback Features 22 ENChanging display information Checking tape positionAutomatic operations after Adjusting tracking conditionSelecting monitor sound Locating beginning of timer Access distant code24 EN Locating beginningBasic RecordingSelect recording channel Set tape speedBasic Recording Features 26 ENSpecifying recording length Watching one program while recording anotherShowing on-screen display Display VCR status on TV screenErase on-screen display Accidental erasure preventionSpecial Effect Playback 28 ENLocating particular scene Rapidly Picture Search High-Speed Picture SearchViewing still picture Skipping unwanted portionsViewing slow motion picture Pause during playbackVCR Plus+ Timer Programing 30 ENEngage timer recording standby mode To use the VCR while it is in timer recording standby modeInput receiving channel number Press SP/EPVCR Plus+ guide channel matching VCR Plus+ Setup32 EN Access Guide Channel Set screen Input guide channel numberExpress Timer Programing 34 ENTo timer-record daily Monday-Friday or weekly serials Checking program settings 36 ENOverlapping programs blink on the screen Confirm overlapping programsSelect program to modify Useful Function Settings Change setting38 EN Select FunctionWhen this function is set to on When this function is set to OFF40 EN For ExampleThis VCR Preventing 42 ENEdit To Or From Another ConnectionEdit From Camcorder 44 ENThis VCR for recording Camcorder for playbackSelect input mode on this VCR Access Main Menu screen on this VCREnable remote pause function Select Edit for Picture ControlTV Brand Setting 46 ENTurn on the TV Set TV brand codeCable Box Brand Setting Turn on the cable boxEnter cable box brand code Operate cable boxDBS Receiver Brand Setting 48 ENTurn on the DBS receiver Enter DBS receiver brand codeChanging Remote Control Code Set remote control code for RemoteUnplug VCR Plug in VCRTroubleshooting 50 ENTimer Recording Other Problems 52 ENCan the VCR indefinitely remain in still mode? What happens if the tape reaches its end during recording?54 EN List of termsFront panel Front display panelOn-screen display 56 ENRear panel How to use the Remote Remote58 EN Usable cassettesFull-Size VHS 30 ST-30 Compact VHS* TC-20 ST-C20 TC-30 ST-C30 TC-40 ST-C40HOW to Locate Your JVC Service Center Limited Warranty 60 ENMemo 62 EN Page HR-VP782U