JVC HR-VP782U manual To timer-record daily Monday-Friday or weekly serials

Page 35
PROGRAM 1

EN 35

8 Set tape speed

Press SP/EP to set the tape speed.

9Return to normal screen

Press PROG. or OK.

“PROGRAM COMPLETED” appears on the screen for about 5 seconds, then normal screen appears.

•If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears, you have another program overlapping the program you have just made.

The Program Check screen appears and conflicting programs will start blinking.

You can now correct the conflicting programs. See “When programs overlap each other” on page 37.

0Engage timer recording standby mode

Press TIMER.

The VCR turns off automatically and “ä” is displayed on the front panel display.

NOTES:

Even if a power failure occurs, the VCR keeps your timer programs. However, the clock time, channel settings, and other menu settings are lost if it lasts for more than 3 minutes. As a result, when the power is supplied again to this VCR after the power failure, the following will take place.

1.This VCR starts the Plug & Play setting automatically to restore the clock time and channel setting.

2.If the clock time and channel setting are restored correctly, each timer program you have made will start unless its end time already passes.

Programs that start after midnight must have the next day’s date.

After timer recording is completed, the VCR turns off automatically.

You can program the timer recording while a regular recording is in progress; the menu screens will not be recorded.

If the tape reaches its end during timer recording, the cassette is automatically ejected.

To timer-record cable or satellite channels, be sure to keep the cable box or DBS receiver turned on.

To timer-record daily (Monday–Friday) or weekly serials

Press DAILY (M-F)(number “8”) or WEEKLY (number “9”) anytime during steps 3 through 9.

“DAILY” or “WEEKLY” appears on the Program screen. Pressing the button again makes the corresponding indication disappear.

To use the VCR while it is in timer recording standby mode

Press TIMER to cancel the timer recording standby mode, then press POWER to turn on the VCR.

DO NOT forget to put the VCR into timer recording standby mode again by pressing TIMER after you use the VCR; otherwise, you cannot record the broadcast you want.

When “AUTO TIMER” ( pg. 39) is set to “ON”, the timer recording standby mode is automatically engaged when the VCR is turned off. It is temporarily canceled when the VCR is turned on. You do not have to press TIMER to engage or disengage the timer recording standby mode.

ATTENTION FOR DBS RECEIVER USERS

If you are using a DBS receiver (unless “DBS

RECEIVER SET” is set to

 

START

STOP

 

8:00AM

 

=

 

9:00PM

 

“OFF”

pg. 19), the band

 

DATE

 

 

 

CH

 

 

12/24/00

 

 

 

110

 

SP

 

 

indication (TV, CATV or

 

 

 

 

 

 

 

SAT

 

 

 

DBS

 

 

 

DBS) appears under the

PRESS (+/–, SP/EP, 8=DAILY,

 

9=WEEKLY, 7=DBS), THEN (0K)

channel number

PRESS (PROG.) TO END

 

 

 

 

 

 

 

 

 

 

indication.

 

 

 

 

 

 

 

 

 

 

TV

:To timer-record a regular TV broadcast

 

received on the VCR.

 

 

 

 

 

 

 

 

 

 

CATV

:To timer-record a cable TV broadcast

 

received on the VCR, or through a cable box

 

(unless “CABLE BOX SET” is set to “OFF”

 

pg. 16).

 

 

 

 

 

 

 

 

 

 

DBS

:To timer-record a satellite broadcast

 

received through a DBS receiver.

 

 

 

 

 

NOTE:

If “BAND” is set to “TV” on the Tuner Set screen ( pg. 13) and “CABLE BOX SET” is set to “OFF” on the Cable Box Set screen ( pg. 16), “CATV” will not be displayed on the Program screen; If “BAND” is set to “CATV” or “CABLE BOX SET” is set to “ON”, “TV” will not be displayed.

If the channel number entered requires that the band be set, “7=DBS” is displayed on the screen.

If this happens, press the Number key “7 (DBS)” to select “DBS”.

Page 34 Page 36
Image 35
Page 34 Page 36
Contents HR-VP782U Telephone Number Dear CustomerGrounding or Polarization Power SourcesPower Lines Power Cord ProtectionReplacement Parts AccessoriesDamage Requiring Service CleaningContents Coaxial cable Audio OUT not supplied AC Power CordBasic Connections Antenna or cableFinal preparation for use Check contentsSituate VCR Connect VCR to TVClock and tuner channels will be set automatically Plug & Play SettingPerform Plug & Play setup What to do if Plug & Play setting failedReturn to normal screen Language SettingAccess Initial Set screen Select languagePreparations Clock Setting10 EN Select time zone Setting clock semiautomaticallySet Auto Clock to on Select host channelManual Clock Set Setting clock manuallySelect D.S.T. mode 12 ENPerform Auto Channel Set Tuner SettingAccess Tuner Set screen Add or skip desired channels Setting channels manuallyAccess Manual Channel Set screen 14 ENConnect cable box to VCR Cable Box Control SettingSituate Controller Attach ControllerTurn on cable box Access Main Menu screen on VCRAccess Cable Box Set screen 16 ENIf the cable boxs channel does not change to AccessPress OKCable. Box Brand Set screenEnter cable box brand Controller How to control the DBS receiver18 EN Connect DBS receiver to VCRSelect DBS receiver output channel Access DBS Receiver Set screenTurn on DBS receiver Enter DBS Receiver’s brand Access DBS Receiver Brand Set screen20 EN Start playback Basic PlaybackLoad a cassette Checking tape position Basic Playback Features22 EN Changing display informationAutomatic operations after Adjusting tracking conditionSelecting monitor sound Locating beginning Locating beginning of timerAccess distant code 24 ENSet tape speed BasicRecording Select recording channelWatching one program while recording another Basic Recording Features26 EN Specifying recording lengthAccidental erasure prevention Showing on-screen displayDisplay VCR status on TV screen Erase on-screen displayRapidly Picture Search High-Speed Picture Search Special Effect Playback28 EN Locating particular scenePause during playback Viewing still pictureSkipping unwanted portions Viewing slow motion picture30 EN VCR Plus+ Timer ProgramingPress SP/EP Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Input receiving channel numberVCR Plus+ guide channel matching VCR Plus+ Setup32 EN Input guide channel number Access Guide Channel Set screen34 EN Express Timer ProgramingTo timer-record daily Monday-Friday or weekly serials 36 EN Checking program settingsOverlapping programs blink on the screen Confirm overlapping programsSelect program to modify Select Function Useful Function SettingsChange setting 38 ENWhen this function is set to OFF When this function is set to onFor Example 40 ENThis VCR 42 EN PreventingConnection Edit To Or From AnotherCamcorder for playback Edit From Camcorder44 EN This VCR for recordingSelect Edit for Picture Control Select input mode on this VCRAccess Main Menu screen on this VCR Enable remote pause functionSet TV brand code TV Brand Setting46 EN Turn on the TVOperate cable box Cable Box Brand SettingTurn on the cable box Enter cable box brand codeEnter DBS receiver brand code DBS Receiver Brand Setting48 EN Turn on the DBS receiverPlug in VCR Changing Remote Control CodeSet remote control code for Remote Unplug VCR50 EN TroubleshootingTimer Recording 52 EN Other ProblemsWhat happens if the tape reaches its end during recording? Can the VCR indefinitely remain in still mode?List of terms 54 ENFront display panel Front panelOn-screen display 56 ENRear panel Remote How to use the RemoteCompact VHS* TC-20 ST-C20 TC-30 ST-C30 TC-40 ST-C40 58 ENUsable cassettes Full-Size VHS 30 ST-30HOW to Locate Your JVC Service Center 60 EN Limited WarrantyMemo 62 EN Page HR-VP782U
Top Page Image Contents