JVC SR-9080 appendix Canceling/Changing Timer Recording, Program, 1To modify timer programs

6 RECORDING
6-3	Timer Recording
				[SHIFT 7] button
				[RESET/CANCEL] button				[SHIFT f] button
				�	RESET/
				SR-9080U
						ON SCREEN
				REC	CANCEL
	REC	STOP REC		EJECT OPERATE			SHIFT
					MENU	TIME MODE
		CHECK	OPERATE
			HDR	RESET/
				CANCEL ON SCREEN
	REW REVERSE PAUSE PLAY FF			SHIFT
		TRACKING	V. LOCK TIMER SEARCH DISPLAY LOCK CNT RESET	MENU TIME MODE
	FIELD REV	– +	– +	– S E T +		–	S E T	+
		FIELD ADV
		[TIMER] button		[MENU] button				[SET +] button
					[SET –] button

	6 RECORDING
	6-3 Timer Recording
Notes on Timer Recording
5		If you make a mistake when programming or no
		program is set and the [TIMER] button is pressed, the
		TIMER	indication blinks for about 10 seconds and a
		warning buzzer sounds if <WARNING> in the
		<BUZZER> menu is set to “ON”.
	=
		Perform programming for timer recording
5		If programmed data overlap
		When the [TIMER] button is pressed, the Timer-
		Recording Standby mode is engaged and the
		[OVERLAP] indication blinks for about 10 seconds, then
		lights.
		(However, if program timer settings and holiday timer

5 During timer recording
The [PAUSE] or [STOP] button has no effect.
=
Operation after pressing the [TIMER] button.
5 Timer recording
The operating mode is turned on about 20 seconds
before recording starts and the VCR pauses. Recording
starts about 2 seconds before the actual programmed
start time.
5 If no cassette is loaded
The TIMER and [	] indications blink and a warning
buzzer sounds if <WARNING> in the <BUZZER> menu
is set to “ON”.
=
Load a cassette with safety tab. Cassettes with no tab

Canceling/Changing Timer Recording
Program
1To stop timer programming before finishing
	Press the [RESET/CANCEL] button.
2	[The program being set is canceled.
	Press the [MENU] button twice.
	[The normal screen mode is restored.
1To cancel preset timer programs
	Press the [TIMER] button so that the	TIMER	indication
2goes out on the display.
3Turn on the VCR and monitor.
	Press the [MENU] button to show the main menu screen
	and press the [SHIFT 7] button to select <PROGRAM
	TIMER> or <HOLIDAY SET>. Then, press the [SET +/–]
	button.
	[The <PROGRAM TIMER> or <HOLIDAY SET> menu
4	is shown on the monitor.
	Press the [SHIFT 7] button or [SHIFT f] button to move
5the cursor to the program you want to cancel.
	Press the [RESET/CANCEL] button.
6	[The specified timer recording program is canceled.
	Press the [MENU] button twice.
	[The normal screen is restored.

1To modify timer programs
	Press the [TIMER] button so that the TIMER indication
2goes out on the display.
3Turn on the VCR and monitor
	Press the [MENU] button to show the main menu screen
	and press the [SHIFT 7] button to select <PROGRAM
	TIMER or <HOLIDAY SET>. Then, press the [SET +/–]
	button.
	[The <PROGRAM TIMER> or <HOLIDAY SET> menu
4	is shown on the monitor.
	Press the [SHIFT 7] button or [SHIFT f] button so that
5the section you want to change blinks.
6Press the [SET +/–] button to change the value.
	Press the [MENU] button twice.
	[The normal screen is restored.
To use the VCR when the Timer-Recording
Standby mode is engaged

•Press the [TIMER] button so that the TIMER indication goes out. After using the VCR, press the [TIMER] button again to engage the Timer-Recording Standby mode. The TIMER indication will light.

•When all timer recording programs are completed, the TIMER indication goes out.

	settings overlap, the [OVERLAP] indication is not
	shown. In this case, the holiday timer setting has
	priority. The [OVERLAP] indication is not shown when a
	daily timer recording program overlaps with another
	program (even during program timer setting). The
	program with the earlier start time has priority.)
	=
	Check the program contents.
	(With program timer settings, the program with the
	earlier program time has priority.)
5	When more than one timer recording is programmed
	=

•The preset programs are executed consecutively beginning with the program with the earliest start time.

The number of the program being executed blinks.

*Program numbers are not displayed for holiday timer recording programs.

5	When the timer recording mode is engaged after the
	start time has passed ....
	When a power failure occurs within the set times and
	power is restored ..
	=
	• Timer recording starts within the set times.
	* If holiday timer and program timer settings overlap, the
	holiday timer setting has priority and starts.
	* When program timer settings overlap, the program with
	the lower program number has priority and starts.
5	When the timer recording settings are changed during
	timer recording
	=
	Changing the settings on the program timer setting
	screen or holiday timer setting screen during timer
	recording will have no effect. To change the settings,
	you must disengage the timer recording mode.

are ejected.

5 When the tape ends during timer recording

=

The cassette tape is ejected.

When a cassette with safety tab is loaded, the timer

recording re-starts.

*However, if timer recording is executed in the Repeat Record mode, the cassette tape is not ejected at the tape end and repeat recording continues.

36 37