JVC LPT0641-001A Locate the end point, Prepare the source tape, Start Random Assemble Editing

Page 65

EN 65

F Locate the end point.

Press PLAY (4) to start playback. Find the edit-out point where you want the edited scene to end by pressing PAUSE (9), then press IN/OUT.

● The edit-out point is registered in memory and appears on the screen.

●The total time of the edited

scenes is displayed to the right of “TOTAL”.

● Repeat steps 5 and 6 for each additional scene.

G Prepare the source tape.

Rewind the tape in the DV deck to the beginning of the scene you want to edit.

H Prepare the VHS deck for dubbing.

APress S-VHS.

BSearch for the point where you want to start dubbing by pressing PLAY (4), FF (5) or REW (3) then press STOP (8).

CPress REC (7), then the VHS deck enters the Record Pause mode.

I Start Random Assemble Editing.

Press START (or OK).

●Automatic editing begins; all the specified scenes are copied to the VHS deck in the order they were registered.

●The on-screen display remains while your VCR searches for each scene (blinking cursor indicates scene currently being searched for), but disappears during actual editing.

●During scene search, the VHS deck automatically enters its Record-Standby mode.

●When all registered scenes have been edited, the DV deck enters the Pause mode, the VHS deck enters its Record Pause mode, and “– : – – : – –” blinks at the next available number.

J End Random Assemble Editing.

Press R.A.EDIT twice to return to the normal screen. Press STOP (8) to stop the VHS deck’s Record Pause mode.

Press DV, then press STOP (8) to stop the DV deck’s Pause mode.

To Make Corrections ...

... in step 5 or 6, you can cancel registered in and out points by pressing CANCEL. Each time you press, the preceding point is erased.

●If, for example, you have registered 5 sets of in and out points and want to reset the first set, you have to press CANCEL until all points after the first set have been erased. Reenter them after you have repaired the first set of points.

NOTES:

●When Random Assemble Editing does not work, press , then perform Random Assemble Editing again.

●To cancel the registered scene, press CANCEL. Each time CANCEL is pressed, the latest registered scene is erased.

●When the source tape has more than 2 identical time codes ( pg. 41), the VCR may not find the edit-in point you set and a malfunction may occur.

●When choosing a scene, set edit-in and edit-out points so that there's a relatively large difference between them.

●If the search time for an in-point exceeds 5 minutes, the VHS deck's Record-Pause mode will be cancelled and editing will not take place.

●If there are blank portions before or after the edit-in and edit- out points, a blue-backed screen may be included in the edited version.

●Since time codes register time only as accurately as seconds, the time code total time may not match the total program time exactly.

●To use Random Assemble Editing consecutively for two or more programs, press START for each program.

When dubbing from another Mini DV cassette, change the Mini DV cassette first, and then press START.

Page 64 Page 66
Image 65
Page 64 Page 66
Contents For Customer Use Video Cassette RecorderMoisture Condensation Dear CustomerImportant Product Safety Instructions Cleaning AccessoriesDamage Requiring Service Replacement PartsContents Front View Rear View Front Display Panel Remote How To UseON-SCREEN Display for VHS deck 10 ENTo recall an indication Press DISPLAY/OSDON-SCREEN Display for DV deck Connect the VCR to power source Check the contents12 EN Situate the VCRVideo Connection 8To connect to a TV with S-VIDEO/AUDIO input connectorsWhat to do if Plug & Play setting failed Perform Plug & Play setupPlug & Play Set 14 ENLanguage Clock Set Access the Clock Set screen16 EN PreparationsManual Clock Set Semiauto Clock SetTuner Set Access the Tuner Set screen18 EN Auto Channel SetAdd or skip the desired channels Manual Channel SetTo add channels To skip channels20 EN Installing ControllerTurn on the cable box Access the Cable Box Set screenSelect the cable box’s channel If you do not use a cable box, press rt until OFFEnter the cable box’s brand 22 ENPress OK or e If the cable box’s channel does not change toDBS receiver If your DBS receiver has audio/video output connectorsHow to control the DBS receiver Turn on the DBS receiver Setting DBS receivers brand and channelSelect the DBS receiver’s channel If you do not use a DBS receiver, press rt until OFFIf the DBS receiver’s channel does not change as shown above Enter the DBS receiver’s brandVHS deck Basic Playback26 EN Set the tape speed Choose a programStart recording Pause/Resume recordingSlow Motion On the VCR 28 ENPause during playback Activate frame-by-frame playbackVariable Speed Search On the Remote Slow Motion On the RemoteIndex Search 30 ENRepeat Playback Next Function MemoryManual Tracking Adjust the tracking manuallySoundtrack Selection Override automatic trackingRecord One Program While Watching Another Instant Timer Recording ITR32 EN Press C.RESET before starting recording or playback Reset the counterTape Remaining Time Set the counter displaySecond Audio Recording 34 ENRetake Recording Active Video CalibrationPlayback DV deck 36 ENSelect the DV deck Press DVDV recording indicator lights on the VCR 38 EN Slow Motion On the Remote 40 EN Time Code Access the VCR Plus+ Program screen Access the PlusCode No. screen42 EN Select the deckFor the VHS deck Engage the VCR’s timer modeFor the DV deck Cable Box or DBS Receiver Users44 EN Access the Guide Channel Set screenGuide Channel Number Set Enter the Guide Channel numberEnter the receiving channel position number Guide Channel Number46 EN Express Timer ProgramingEnter the channel position Enter the program datePress DATE+ Press CH+24HR Quick Programing Enter the program mode48 EN Set the program start/stop time and channelPage Access the Program Check screen Disengage the timer modeCancel or change a program Return to the timer modeConfirm the overlapping programs Cancel or change program settingSelect the program to modify Overlapping programs blink on the TV screen52 EN Tape DubbingFrom DV to VHS Dubbing An Entire CassettePress DV, then press SP/LP p From VHS to DVLocate the start point on the DV deck 54 ENPrepare the VHS deck for dubbing Pause dubbingPrepare the DV deck for dubbing Locate the start point on the VHS deck56 EN Player Recorder58 EN Set the input mode of recording deckStart the source player Start the recording deckExample When using this VCR as the source player Connection to a PC with DV connectorPC with DV connector Connection to another VCR60 EN Audio DubbingVHS Audio Dubbing DV Audio DubbingPress A.DUB Engage the Audio Dubbing modeEnd Audio Dubbing 62 EN Insert EditingVHS Insert Editing Source tapeAV Insert Editing VHS deck only Engage the Insert Editing modePrepare the recording cassette Start Editing64 EN Access the R.A.Edit screenSelect the program Press R.A.EDIT. The R.A.Edit screen appearsPrepare the source tape Locate the end pointStart Random Assemble Editing End Random Assemble Editing66 EN Remote A/B Code SwitchingChange the code for VCR To control two VCRs with the same RemoteSet the TV brand code TV Multi-Brand Remote ControlOperate the TV Before performing the following steps68 EN Press the corresponding button PowerSet the Cable Box brand code Operate the Cable BoxOperate the DBS receiver DBS Receiver Multi-Brand Remote ControlSet the DBS receiver brand code Access the Mode Set screen Mode SetSelect the mode Select the mode settingWhen this function is set to on Mode SET72 EN VHS Mode SETVHS Mode SET For Example 74 ENSelecting either HI-FI L or HI-FI R Correction to the luminance signal to enhance detailsNormally select this. Hi-Fi sound is played back Sound on the left Hi-Fi channel is played back76 EN DV Mode SETPower Recording 78 ENDV deck VHS deck80 EN Timer RecordingRecording Timer RecordingPlayback 82 EN Changing VCR Plus+ Setting Cable box Cable Box Control SettingExpress Timer Programming VCR Plus+ Timer Programing84 EN HOW to Locate Your JVC Service CenterWarranty Only in U.S.A 86 EN
Top Page Image Contents