JVC LPT0641-001A manual VHS deck, DV deck

Page 79

			EN 79
TIMER RECORDING
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Timer recording won’t work.	● The clock and/or the timer have been set	Re-perform the clock and/or timer
		incorrectly.	settings.
		● The timer is not engaged.	Press TIMER and confirm that “#” is
			displayed on the front display panel.
		● Timer recording may not work when the	Set the channel position other than “F-1”
		VCR’s input mode is set to “F-1” for	before engaging to Timer-Standby mode.
		recording on the DV deck.

2.	Timer programing is not possible.	● Timer recording is in progress.	Timer programing can’t be performed
			while a timer recording is in progress.
			Wait until it finishes.

3.	“#” and “[” on the front display	● The timer is engaged but there’s no	For the VHS deck
	panel won’t stop blinking.	cassette loaded.	Insert a VHS (or S-VHS) cassette with the
			record safety tab intact, or cover the hole
			using adhesive tape.
			For the DV deck
			Insert a Mini DV cassette with the erase
			protection switch set to “REC”.
		● The end of the tape was reached during	The program may not have been recorded
		timer recording.	in its entirety. Next time make sure you
			have enough time on the tape to record
			the entire program.
		● VHS deck
		The loaded cassette has had its record	Remove the cassette and cover the hole
		safety tab removed.	with adhesive tape, or insert a cassette
			with the record safety tab intact.
		● DV deck
		The loaded cassette has had its erase	Remove the cassette and set the erase
		protection switch set to “SAVE”.	protection switch to “REC”.

4.	“#” blinks for 10 seconds and the	● TIMER has been pressed when there are	Check the programed data and re-
	Timer mode is disengaged.	no programs in memory, or the timer	program as necessary, then press TIMER
		record information has been programed	again.
		incorrectly.

5.	The VCR Plus+ system does not timer-	● The VCR’s channel positions have been	Refer to “Guide Channel Number Set”
	record properly.	set incorrectly.	( pg. 44) and re-perform the procedure.

6.	The power shuts off and “[” won’t	● The end of the tape was reached during	The program may not have been recorded
	stop blinking.	Instant Timer Recording.	in its entirety. Next time make sure you
			have enough time on the tape to record
			the entire program.

Image 79

Contents For Customer Use Video Cassette RecorderMoisture Condensation Dear CustomerImportant Product Safety Instructions Replacement Parts AccessoriesCleaning Damage Requiring ServiceContents Front View Rear View Front Display Panel Remote How To UsePress DISPLAY/OSD 10 ENON-SCREEN Display for VHS deck To recall an indicationON-SCREEN Display for DV deck Situate the VCR Check the contentsConnect the VCR to power source 12 ENVideo Connection 8To connect to a TV with S-VIDEO/AUDIO input connectors14 EN Perform Plug & Play setupWhat to do if Plug & Play setting failed Plug & Play SetLanguage Preparations Access the Clock Set screenClock Set 16 ENManual Clock Set Semiauto Clock SetAuto Channel Set Access the Tuner Set screenTuner Set 18 ENTo skip channels Manual Channel SetAdd or skip the desired channels To add channels20 EN Installing ControllerIf you do not use a cable box, press rt until OFF Access the Cable Box Set screenTurn on the cable box Select the cable box’s channelIf the cable box’s channel does not change to 22 ENEnter the cable box’s brand Press OK or eHow to control the DBS receiver If your DBS receiver has audio/video output connectorsDBS receiver If you do not use a DBS receiver, press rt until OFF Setting DBS receivers brand and channelTurn on the DBS receiver Select the DBS receiver’s channelIf the DBS receiver’s channel does not change as shown above Enter the DBS receiver’s brand26 EN Basic PlaybackVHS deck Pause/Resume recording Choose a programSet the tape speed Start recordingActivate frame-by-frame playback 28 ENSlow Motion On the VCR Pause during playbackVariable Speed Search On the Remote Slow Motion On the RemoteNext Function Memory 30 ENIndex Search Repeat PlaybackOverride automatic tracking Adjust the tracking manuallyManual Tracking Soundtrack Selection32 EN Instant Timer Recording ITRRecord One Program While Watching Another Set the counter display Reset the counterPress C.RESET before starting recording or playback Tape Remaining TimeRetake 34 ENSecond Audio Recording Playback Active Video CalibrationRecording Press DV 36 ENDV deck Select the DV deckDV recording indicator lights on the VCR 38 EN Slow Motion On the Remote 40 EN Time Code Select the deck Access the PlusCode No. screenAccess the VCR Plus+ Program screen 42 ENCable Box or DBS Receiver Users Engage the VCR’s timer modeFor the VHS deck For the DV deckEnter the Guide Channel number Access the Guide Channel Set screen44 EN Guide Channel Number SetEnter the receiving channel position number Guide Channel Number46 EN Express Timer ProgramingPress CH+ Enter the program dateEnter the channel position Press DATE+Set the program start/stop time and channel Enter the program mode24HR Quick Programing 48 ENPage Return to the timer mode Disengage the timer modeAccess the Program Check screen Cancel or change a programOverlapping programs blink on the TV screen Cancel or change program settingConfirm the overlapping programs Select the program to modifyDubbing An Entire Cassette Tape Dubbing52 EN From DV to VHSPress DV, then press SP/LP p From VHS to DVPause dubbing 54 ENLocate the start point on the DV deck Prepare the VHS deck for dubbingPrepare the DV deck for dubbing Locate the start point on the VHS deck56 EN Player RecorderStart the recording deck Set the input mode of recording deck58 EN Start the source playerConnection to another VCR Connection to a PC with DV connectorExample When using this VCR as the source player PC with DV connectorDV Audio Dubbing Audio Dubbing60 EN VHS Audio DubbingEnd Audio Dubbing Engage the Audio Dubbing modePress A.DUB Source tape Insert Editing62 EN VHS Insert EditingStart Editing Engage the Insert Editing modeAV Insert Editing VHS deck only Prepare the recording cassettePress R.A.EDIT. The R.A.Edit screen appears Access the R.A.Edit screen64 EN Select the programEnd Random Assemble Editing Locate the end pointPrepare the source tape Start Random Assemble EditingTo control two VCRs with the same Remote Remote A/B Code Switching66 EN Change the code for VCRBefore performing the following steps TV Multi-Brand Remote ControlSet the TV brand code Operate the TVOperate the Cable Box Press the corresponding button Power68 EN Set the Cable Box brand codeSet the DBS receiver brand code DBS Receiver Multi-Brand Remote ControlOperate the DBS receiver Select the mode setting Mode SetAccess the Mode Set screen Select the modeWhen this function is set to on Mode SET72 EN VHS Mode SETVHS Mode SET For Example 74 ENSound on the left Hi-Fi channel is played back Correction to the luminance signal to enhance detailsSelecting either HI-FI L or HI-FI R Normally select this. Hi-Fi sound is played back76 EN DV Mode SETPower Recording 78 ENDV deck VHS deck80 EN Timer RecordingPlayback Timer RecordingRecording 82 EN VCR Plus+ Timer Programing Cable box Cable Box Control SettingChanging VCR Plus+ Setting Express Timer Programming84 EN HOW to Locate Your JVC Service CenterWarranty Only in U.S.A 86 EN