JVC LPT0641-001A manual 30 EN, Index Search, Repeat Playback, Next Function Memory

Page 30

30 EN

PLAYBACK/RECORDING ON VHS DECK (cont.)

1

3

2

T

W

1 2 3

2

4 5 6

7 8 9

04

1		DV	S-VHS

Index Search

Your VCR automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction.

NOTE:	INDEX 1

Before starting, make sure the VCR is in the Stop mode.

Activate Index Search.

Press w or e (2 or 6). “INDEX -1” or “INDEX 1” is displayed on the TV screen and search begins in the corresponding direction.

●To access index codes 2 through 9, press w or e repeatedly until the correct index number is displayed.

Example:

To locate the beginning of B from the current position, press w twice.

To locate the beginning of D from the current position, press e once.

Current position

Index number

●When the specified index code is located, playback begins automatically.

Repeat Playback

Your VCR can automatically play back the whole tape 100 times repeatedly.

1Start playback.

Press PLAY (4).

2Activate Repeat Playback.

Press PLAY (4) and hold for over 5 seconds, then release.

●The Play indicator ( u) on the front display panel blinks slowly.

●After playing back a tape 100 times, the VCR stops automatically.

3Stop Repeat Playback.

Press STOP (8) at any time.

●Pressing PLAY (4), REW (3), FF (5) or PAUSE (9) also stops Repeat Playback.

Next Function Memory

The Next Function Memory “tells” the VCR what to do after rewinding. Before continuing, make sure the VCR is in the Stop mode.

a- For Automatic Start Of Playback

Press REW (3), then press PLAY (4) within 2 seconds.

b- For Automatic Power Off

Press REW (3), then press POWER within 2 seconds.

c- For Automatic Cassette Ejection After Tape Rewind Press REW (3), then press EJECT () within

2 seconds.

NOTE:

The Automatic Power Off does not work if “AUTO TIMER” is set to “ON” ( pg. 71) and if any timer programing has been made. If “AUTO TIMER” is set to “ON”, the VCR directly goes into the Timer-Standby mode at the same time when the POWER is pressed for the Automatic Power Off.

Image 30

Contents Video Cassette Recorder For Customer UseDear Customer Moisture CondensationImportant Product Safety Instructions Damage Requiring Service AccessoriesCleaning Replacement PartsContents Front View Rear View Front Display Panel How To Use RemoteTo recall an indication 10 ENON-SCREEN Display for VHS deck Press DISPLAY/OSDON-SCREEN Display for DV deck 12 EN Check the contentsConnect the VCR to power source Situate the VCR8To connect to a TV with S-VIDEO/AUDIO input connectors Video ConnectionPlug & Play Set Perform Plug & Play setupWhat to do if Plug & Play setting failed 14 ENLanguage 16 EN Access the Clock Set screenClock Set PreparationsSemiauto Clock Set Manual Clock Set18 EN Access the Tuner Set screenTuner Set Auto Channel SetTo add channels Manual Channel SetAdd or skip the desired channels To skip channelsInstalling Controller 20 ENSelect the cable box’s channel Access the Cable Box Set screenTurn on the cable box If you do not use a cable box, press rt until OFFPress OK or e 22 ENEnter the cable box’s brand If the cable box’s channel does not change toIf your DBS receiver has audio/video output connectors How to control the DBS receiverDBS receiver Select the DBS receiver’s channel Setting DBS receivers brand and channelTurn on the DBS receiver If you do not use a DBS receiver, press rt until OFFEnter the DBS receiver’s brand If the DBS receiver’s channel does not change as shown aboveBasic Playback 26 ENVHS deck Start recording Choose a programSet the tape speed Pause/Resume recordingPause during playback 28 ENSlow Motion On the VCR Activate frame-by-frame playbackSlow Motion On the Remote Variable Speed Search On the RemoteRepeat Playback 30 ENIndex Search Next Function MemorySoundtrack Selection Adjust the tracking manuallyManual Tracking Override automatic trackingInstant Timer Recording ITR 32 ENRecord One Program While Watching Another Tape Remaining Time Reset the counterPress C.RESET before starting recording or playback Set the counter display34 EN RetakeSecond Audio Recording Active Video Calibration PlaybackRecording Select the DV deck 36 ENDV deck Press DVDV recording indicator lights on the VCR 38 EN Slow Motion On the Remote 40 EN Time Code 42 EN Access the PlusCode No. screenAccess the VCR Plus+ Program screen Select the deckFor the DV deck Engage the VCR’s timer modeFor the VHS deck Cable Box or DBS Receiver UsersGuide Channel Number Set Access the Guide Channel Set screen44 EN Enter the Guide Channel numberGuide Channel Number Enter the receiving channel position numberExpress Timer Programing 46 ENPress DATE+ Enter the program dateEnter the channel position Press CH+48 EN Enter the program mode24HR Quick Programing Set the program start/stop time and channelPage Cancel or change a program Disengage the timer modeAccess the Program Check screen Return to the timer modeSelect the program to modify Cancel or change program settingConfirm the overlapping programs Overlapping programs blink on the TV screenFrom DV to VHS Tape Dubbing52 EN Dubbing An Entire CassetteFrom VHS to DV Press DV, then press SP/LP pPrepare the VHS deck for dubbing 54 ENLocate the start point on the DV deck Pause dubbingLocate the start point on the VHS deck Prepare the DV deck for dubbing56 EN Recorder PlayerStart the source player Set the input mode of recording deck58 EN Start the recording deckPC with DV connector Connection to a PC with DV connectorExample When using this VCR as the source player Connection to another VCRVHS Audio Dubbing Audio Dubbing60 EN DV Audio DubbingEngage the Audio Dubbing mode End Audio DubbingPress A.DUB VHS Insert Editing Insert Editing62 EN Source tapePrepare the recording cassette Engage the Insert Editing modeAV Insert Editing VHS deck only Start EditingSelect the program Access the R.A.Edit screen64 EN Press R.A.EDIT. The R.A.Edit screen appearsStart Random Assemble Editing Locate the end pointPrepare the source tape End Random Assemble EditingChange the code for VCR Remote A/B Code Switching66 EN To control two VCRs with the same RemoteOperate the TV TV Multi-Brand Remote ControlSet the TV brand code Before performing the following stepsSet the Cable Box brand code Press the corresponding button Power68 EN Operate the Cable BoxDBS Receiver Multi-Brand Remote Control Set the DBS receiver brand codeOperate the DBS receiver Select the mode Mode SetAccess the Mode Set screen Select the mode settingMode SET When this function is set to onVHS Mode SET 72 ENVHS Mode SET 74 EN For ExampleNormally select this. Hi-Fi sound is played back Correction to the luminance signal to enhance detailsSelecting either HI-FI L or HI-FI R Sound on the left Hi-Fi channel is played backDV Mode SET 76 ENPower 78 EN RecordingVHS deck DV deckTimer Recording 80 ENTimer Recording PlaybackRecording 82 EN Express Timer Programming Cable box Cable Box Control SettingChanging VCR Plus+ Setting VCR Plus+ Timer ProgramingHOW to Locate Your JVC Service Center 84 ENWarranty Only in U.S.A 86 EN