JVC HR-J239EE manual SET A/B Code Switch, RE-SUPPLY Power, SET Counter Memory, Activate Counter

Page 13

Index Search

Your recorder automatically marks

index codes at the beginning of£ 2 each recording. This function gives

you quick access to any one of 9 index codes in either direction.

NOTE:

Before starting, make sure the recorder is in the Stop mode.

ACTIVATE INDEX SEARCH

1 Press PUSH JOG% or % (ª or £). “ª 1” or “£1” is displayed on screen and search begins in the corresponding direction.

To access index codes 2 through 9, press PUSH JOG

% or % repeatedly until the correct index number is displayed.

Ex.: To locate the beginning of B from the current position, press PUSH JOG % twice.

To locate the beginning of D from the current position, press PUSH JOG %once.

Current position

A

 

B

 

C

 

D

E

 

F

 

 

 

 

 

 

 

 

 

 

 

 

 

–2

 

–1

1

2

3

 

 

 

 

%

 

 

 

%

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Index number

When the specified index code is located, playback begins automatically.

EN13

Remote A/B Code Switching

The remote control is capable of controlling two JVC video recorders independently; one set to respond to the remote control’s A code control signals and another set to respond to B code control signals. The remote control is preset to send A code signals because your video recorder is initially set to respond to A code signals. You can easily modify your video recorder to respond to B code signals.

1

 

REMOVE POWER SUPPLY

 

Unplug the mains power cord from the mains outlet.

2

 

SET A/B CODE SWITCH

 

Set to B.

3

 

RE-SUPPLY POWER

 

Plug the mains power cord back into the mains outlet.

4

 

TURN THE RECORDER ON

 

Press OPERATE on the remote control. The recorder

 

will now only respond to B code signals.

 

 

 

NOTE:

Some TV sets may malfunction in response to the B mode. If this happens, switch back to the A mode.

Counter Memory

Returns to the counter reading of “0:00:00” to conveniently find a specific place on the tape automatically.

1

SET COUNTER MEMORY

Press C. RESET during playback at a point you wish to

locate later. The counter reads “0:00:00”. Then press C.

MEMORY, and “M” appears on the front display panel.

 

ACTIVATE COUNTER

2

MEMORY

When you wish to return to the designated point, press

STOP and then REW or FF.

The tape rewinds or fast-forwards and stops at about

 

 

0:00:00 automatically.

 

To cancel Counter Memory, press C.MEMORY again.

Next Function Memory

You can set your recorder's power to go off automatically after the tape is fully rewound. Before starting, make sure the recorder is in the Stop mode.

For Automatic Power Off After Tape Rewind . . .

. . . press REW, then press OPERATE within 2 seconds.

NOTE:

If you want the power to be turned off automatically when the counter reads “0:00:00” (instead of at the beginning of the tape), press C.MEMORY so that the “M” mark appears before pressing REW.

Image 13
Contents HR-J239EE Contents Safety PrecautionsInstalling Your NEW Record ER EN Check ContentsBasic Connections Situate RecorderSelect Televi- sion System Tune The TV To Your Video RecorderOn-Screen Displays ENABLE/DISABLETurn on the Recorder Select LanguageMode Select Screen Access Channel SETSelect Mode Select BandStore Channel Select PositionSelect Channel Return to Normal ScreenFine-Tuning Channels Perform TuningReturn to Normal Already StoredSET Time Clock SetSET Date SET YearLoad a Cassette Basic PlaybackPoint Start PlaybackPlayback Features Activate Repeat Activate Instant ReviewActivate Scene Finder Stop Scene FinderRE-SUPPLY Power SET A/B Code SwitchSET Counter Memory Activate CounterRecording BasicRecording Features Close Mode Select Screen Access Mode SelectS.T. Picture System SET B.E.S.T. to onPlayback Recorder adjusts the playback picture qualityBased on the quality of the tape in use S.T. is active during Auto TrackingEN Timer Recording Timer ProgrammingTimer Program Enter Programme Stop TimeTimer Timer ModeEngage RECORDER’S Select ProgrammeEdit To Or From Another Video Recorder SET Recording DECK’S Input ModeMake Connections Start Source PlayerEdit From a Camcorder SET RECORDER’S Input ModeStart Camcorder Start RecorderOff-Air Recording Setting Of The Colour System Select ButtonsHR-J239EE Playback equipment Tape-To-Tape EditingDubbed tape Control Your TV Using Addi- tional Buttons Multi-Brand Remote ControlSET TV Brand Code TRY Operating TVOn Next Troubleshooting E NOubleshooting Timer againCheck the programmed data and re Playback Recording Questions and Answer SPrecautions EN SpecificationsDo not place the recorder Do not block the recorder’s ventilation openingsFront View IndexDisplay Panel How To Use Installing BatteriesHR-J239EE