JVC HR-J239EE manual Oubleshooting, Check the programmed data and re, Timer again

Page 26

26EN

TROUBLESHOOTING(cont.)

RECORDING

 

 

 

 

 

 

 

 

 

 

 

SYMPTOM

 

POSSIBLE CAUSE

 

CORRECTIVE ACTION

1.

Recording cannot be started.

 

● There is no cassette loaded, or the

 

Insert a cassette, or using adhesive

 

 

 

cassette loaded has had its Record

 

tape, reseal the slot where the tab

 

 

 

Safety tab removed.

 

was removed.

 

 

 

 

 

2. TV broadcasts cannot be recorded.

 

● “AU” has been selected as the input

 

Set to the desired channel.

 

 

 

mode.

 

 

 

 

 

 

 

 

3.

Tape-to-tape editing is not possible.

 

● The source (another video recorder,

 

Confirm that the source is properly

 

 

 

camcorder) has not been properly

 

connected.

 

 

 

connected.

 

 

 

 

 

● All necessary power switches have

 

Confirm that all units’ power switches

 

 

 

not been turned on.

 

are turned on.

 

 

 

● The input mode is not correct.

 

Set the input mode to “AU”.

 

 

 

 

 

 

4.

Camcorder recording is not

 

● The camcorder has not been

 

Confirm that the camcorder is

 

possible.

 

properly connected.

 

properly connected.

 

 

 

● The input mode is not correct.

 

Set the input mode to “AU”.

 

 

 

 

 

TIMER RECORDING

 

 

 

 

 

SYMPTOM

 

POSSIBLE CAUSE

 

CORRECTIVE ACTION

1.

Timer recording won’t work.

 

● The clock and/or the timer have

 

Re-perform the clock and/or timer

 

 

 

been set incorrectly.

 

settings.

 

 

 

● The timer is not engaged.

 

Press TIMER and confirm that “TIMER“

 

 

 

 

 

is displayed on the display panel.

 

 

 

 

 

 

2.

On-screen timer programming is

 

● Timer recording is in progress.

 

Timer programming can’t be

 

not possible.

 

 

 

performed while a timer recording is

 

 

 

 

 

in progress. Wait until it finishes.

 

 

 

 

 

 

3.

“TIMER“ and “]“ on the display

 

● The timer is engaged but there’s no

 

Load a cassette with the Record

 

panel won’t stop blinking.

 

cassette loaded.

 

Safety tab intact, or cover the hole

 

 

 

 

 

using adhesive tape.

 

 

 

 

 

 

4.

The cassette is automatically

 

● The loaded cassette has had its

 

Remove the cassette and cover the

 

ejected, and “TIMER“ and “]“

 

Record Safety tab removed.

 

hole with adhesive tape, or insert a

 

on the display panel won’t stop

 

 

 

cassette with the Record Safety tab

 

blinking.

 

 

 

intact.

 

 

 

 

 

 

5.

“TIMER“ blinks for 10 seconds and

 

● TIMER has been pressed when there

 

Check the programmed data and re-

 

the Timer mode is disengaged.

 

are no programs in memory, or the

 

program as necessary, then press

 

 

 

timer record information has been

 

TIMER again.

 

 

 

programmed incorrectly.

 

 

 

 

 

 

 

 

6.

The cassette is automatically

 

● The end of the tape was reached

 

The programme may not have been

 

ejected, the power shuts off and

 

during timer recording.

 

recorded in its entirety. Next time

 

“TIMER“ and “]“ won’t stop

 

 

 

make sure you have enough time on

 

blinking.

 

 

 

the tape to record the entire

 

 

 

 

 

programme.

 

 

 

 

 

OTHER PROBLEMS

 

 

 

 

 

SYMPTOM

 

POSSIBLE CAUSE

 

CORRECTIVE ACTION

1.

Whistling or howling is heard from

 

● The camcorder’s microphone is too

 

Position the camcorder so its

 

the TV during camcorder record-

 

close to the TV.

 

microphone is away from the TV.

 

ing.

 

● The TV’s volume is too high.

 

Turn the TV’s volume down.

 

 

 

 

 

 

2.

The channel cannot be changed.

 

● Recording is in progress.

 

Press PAUSE to pause the recording,

 

 

 

 

 

change channels, then press PLAY to

 

 

 

 

 

resume recording.

 

 

 

 

 

 

3.

The remote control won’t operate

 

● The TV/VCR switch is in the wrong

 

Set the switch to TV.

 

the TV.

 

position.

 

 

 

 

 

 

 

 

Page 25 Page 27
Image 26
Page 25 Page 27
Contents HR-J239EE Safety Precautions ContentsBasic Connections Check ContentsInstalling Your NEW Record ER EN Situate RecorderTune The TV To Your Video Recorder Select Televi- sion SystemTurn on the Recorder ENABLE/DISABLEOn-Screen Displays Select LanguageSelect Mode Access Channel SETMode Select Screen Select BandSelect Channel Select PositionStore Channel Return to Normal ScreenReturn to Normal Perform TuningFine-Tuning Channels Already StoredSET Date Clock SetSET Time SET YearPoint Basic PlaybackLoad a Cassette Start PlaybackPlayback Features Activate Scene Finder Activate Instant ReviewActivate Repeat Stop Scene FinderSET Counter Memory SET A/B Code SwitchRE-SUPPLY Power Activate CounterBasic RecordingRecording Features S.T. Picture System Access Mode SelectClose Mode Select Screen SET B.E.S.T. to onBased on the quality of the tape in use Recorder adjusts the playback picture qualityPlayback S.T. is active during Auto TrackingTimer Program Timer ProgrammingEN Timer Recording Enter Programme Stop TimeEngage RECORDER’S Timer ModeTimer Select ProgrammeMake Connections SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Start Source PlayerStart Camcorder SET RECORDER’S Input ModeEdit From a Camcorder Start RecorderHR-J239EE Setting Of The Colour System Select ButtonsOff-Air Recording Dubbed tape Tape-To-Tape EditingPlayback equipment SET TV Brand Code Multi-Brand Remote ControlControl Your TV Using Addi- tional Buttons TRY Operating TVTroubleshooting E N On NextCheck the programmed data and re Timer againOubleshooting Questions and Answer S Playback RecordingDo not place the recorder EN SpecificationsPrecautions Do not block the recorder’s ventilation openingsIndex Front ViewDisplay Panel Installing Batteries How To UseHR-J239EE
Top Page Image Contents