JVC HR-J239EE manual Playback, Recorder adjusts the playback picture quality

Page 17

 

PLAY

2

2

q

5/8

RECORD

1 2 3

4

5

6

7

8

9

 

0

 

 

PLAY

 

PAUSE

RECORD

EN17

NOTES:

●The B.E.S.T. system works for SP, LP and EP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording.

●In the case of timer recording, the B.E.S.T. system works before recording is initiated.

●Once the cassette is ejected, the B.E.S.T. data is cancelled. The next time the cassette is used for recording, B.E.S.T. is re- performed.

ATTENTION:

Since the B.E.S.T. system works before recording actually starts, there is a delay of approximately 7 seconds after RECORD and PLAY on the remote are pressed, or RECORD on the recorder is pressed. To make sure you record the desired scene or programme in its entirety, first perform the following steps:

1)Press and hold PAUSE and RECORD to engage the RECORD PAUSE mode.

●The recorder then automatically checks the condition of the tape and, after approximately 7 seconds, re- enters RECORD PAUSE.

2)Press PLAY to start recording.

●If you want to bypass the B.E.S.T. system and begin recording immediately, set “B.E.S.T.” to “OFF” in step 3 on page 16.

Playback

The recorder assesses the quality of the tape once you initiate playback.

When watching a tape recorded with “B.E.S.T.” set to “ON”, it is recommended that you leave B.E.S.T. on during playback as well.

1

 

START PLAYBACK

 

Press PLAY.

 

 

 

● The recorder adjusts the playback picture quality

 

based on the quality of the tape in use.

 

 

● B.E.S.T. is active during Auto Tracking.

NOTE:

When watching a rental tape, or one recorded on another video recorder, set B.E.S.T. to your preference by performing steps 2 through 4 on page 16.

Page 16 Page 18
Image 17
Page 16 Page 18
Contents HR-J239EE Contents Safety PrecautionsInstalling Your NEW Record ER EN Check ContentsBasic Connections Situate RecorderSelect Televi- sion System Tune The TV To Your Video RecorderOn-Screen Displays ENABLE/DISABLETurn on the Recorder Select LanguageMode Select Screen Access Channel SETSelect Mode Select BandStore Channel Select PositionSelect Channel Return to Normal ScreenFine-Tuning Channels Perform TuningReturn to Normal Already StoredSET Time Clock SetSET Date SET YearLoad a Cassette Basic PlaybackPoint Start PlaybackPlayback Features Activate Repeat Activate Instant ReviewActivate Scene Finder Stop Scene FinderRE-SUPPLY Power SET A/B Code SwitchSET Counter Memory Activate CounterRecording BasicRecording Features Close Mode Select Screen Access Mode SelectS.T. Picture System SET B.E.S.T. to onPlayback Recorder adjusts the playback picture qualityBased on the quality of the tape in use S.T. is active during Auto TrackingEN Timer Recording Timer ProgrammingTimer Program Enter Programme Stop TimeTimer Timer ModeEngage RECORDER’S Select ProgrammeEdit To Or From Another Video Recorder SET Recording DECK’S Input ModeMake Connections Start Source PlayerEdit From a Camcorder SET RECORDER’S Input ModeStart Camcorder Start RecorderHR-J239EE Setting Of The Colour System Select ButtonsOff-Air Recording Dubbed tape Tape-To-Tape EditingPlayback equipment Control Your TV Using Addi- tional Buttons Multi-Brand Remote ControlSET TV Brand Code TRY Operating TVOn Next Troubleshooting E NCheck the programmed data and re Timer againOubleshooting Playback Recording Questions and Answer SPrecautions EN SpecificationsDo not place the recorder Do not block the recorder’s ventilation openingsFront View IndexDisplay Panel How To Use Installing BatteriesHR-J239EE
Top Page Image Contents