JVC HR-J239EE manual Engage RECORDER’S, Timer Mode, Select Programme, Engage Auto SP/LP

ENTER CHANNEL
POSITION
Press TV PROG.5/° to		– P1–
select the channel you	START	STOP
6 wish to record.	21:00	= 22:00
		SP
	DATE	TV PROG.
	25.12	1
	[1–6] [TV PROG5°]
	[PROG./CLOCK] :NEXT

7	SET TAPE SPEED
	Press SP/LP/EP to set the tape speed.
	● For each additional programme, press PROG. and
	repeat steps 3 – 7.
	RETURN TO NORMAL
	SCREEN
	Press PROG. as many times as necessary to return to
8 normal screen.
	ENGAGE RECORDER’S
	TIMER MODE
9 Press TIMER.

To Timer-Record Weekly Or Daily Serials . . .

. . . anytime during steps 3 through 7, press WEEKLY (NUMBER key “9”) for weekly serials or DAILY (NUMBER key “8”) for daily serials (Monday–Friday).

NOTES:

●You can programme this recorder to timer-record as many as 8 programmes. To record the extra programme, you must first cancel any unnecessary programmes (☞ Check And Cancel Programmes).

●For safety, your recorder disables all other functions while in the Timer mode. If you want to use the recorder but its Timer mode is engaged, press TIMER and all other functions are operable. To re-engage the timer, press TIMER.

●In case of a power failure after programming, the recorder’s memory backup keeps your selections for 18 hours.

●Backup time becomes shorter as the unit's internal parts become old. When this occurs, please consult your nearby JVC dealer.

Check And Cancel

Programmes

ACCESS TIMER PROGRAM- MING SCREEN

1 Perform steps 1 and 2 of Timer Programming to call up the Timer Programming screen.

●If the recorder is in the Timer mode, first press TIMER to exit the mode.

EN19

SELECT PROGRAMME

2 Press PROG. until the programme you wish to call up appears.

●Each time you press PROG. the next programme's information appears up to "P8" (Programme 8).

●If you want to make a correction, use NUMBER key "1" – "6" and TV PROG.5/°.

●If you want to cancel a programme, press CANCEL.

RETURN TO NORMAL

SCREEN

3 Press PROG. as many times as necessary to return to normal screen.

●Press TIMER to engage the recorder's timer mode.

Auto SP/LP Timer

If, when recording in SP mode, there is not enough tape to record the entire programme, the recorder automatically switches to LP mode (with PAL broadcasts) or EP mode (with NTSC broadcasts) to allow complete recording.

	ENGAGE AUTO SP/LP
1	TIMER
	Press AUTO SP/LP TIMER on the recorder front panel.
	The AUTO SP/LP TIMER indicator lights “orange”.
	For Example . . .
	Recording a PAL-broadcast program of 210 minutes in
	length onto a 180-minute tape
	Approximately 150 minutes		Approximately 60 minutes
		SP mode	LP mode

Total 210 minutes

Make sure you press AUTO SP/LP TIMER before performing timer programming.

NOTES:

●The Auto SP/LP Timer feature is not available during ITR (Instant Timer Recording), and the feature will not work properly with any tapes longer than E-180 as well as some tapes of shorter lenghs.

●Even if, in step 1, you press AUTO SP/LP TIMER and it lights “orange”, that doesn’t mean that the recorder will automati- cally change from SP to LP (or EP) mode during the course of the recording. Watch the tape later to confirm.

●If you have programmed the recorder to timer-record 2 or more programs, the second programme and those thereafter may not fit on the tape if you engage the Auto SP/LP Timer mode. In this case, make sure the mode is not engaged, then set the tape speed manually during timer programming.

●There may be some noise at the point on the tape where the recorder switches from SP to LP (or EP) mode.