JVC HR-DD845EK setup guide Playback Features, Activate HIGH-SPEED Search, Pause During Playback

Page 13

Playback

Features

IME

 

SCAN

 

SHUTTLE

OJG

 

q

TV PROG

 

PAUSE

PLAY

7

8

9

 

 

0

4

 

 

 

TV PROG

 

LAY

 

 

 

REW

 

FF

 

 

 

 

 

 

PAUSE

 

 

 

3

 

1

 

 

 

PUSH JOG

High-Speed (Turbo) Search

ACTIVATE HIGH-SPEED

SEARCH

1 During playback or still picture, press FF for forward high-speed search, or REW for reverse high-speed search.

To resume normal playback, press PLAY.

NOTES:

For short searches, press and hold FF or REW for over 2 seconds. When released, normal playback resumes.

Picture may not appear during search with an LP-recorded tape.

In the search, still, or frame by frame playback mode, the picture may be distorted, and there may be a loss of colour.

13

Take advantage of special functions possible with the recorder’s controls or the remote control.

Still Picture/Frame-By-Frame Playback

PAUSE DURING PLAYBACK

1 Press PAUSE. If there is vertical jitter, use the TV PROG buttons to correct the picture.

During still picture, the sound from the previous

3 seconds (approx.) will be played back repeatedly (provided there was at least 6 seconds of normal playback prior to engaging the still picture mode).

The "TIME SCAN AUDIO" must be set to "ON", or the sound will not be heard (pg. 19).

ACTIVATE FRAME-BY-FRAME PLAYBACK

2 Turn the JOG dial to the right for forward frame-by- frame playback, or to the left for reverse frame-by-frame playback.

OR

Press PAUSE.

OR

Press PUSH JOG %or %.

To resume normal playback, press PLAY.

Slow Motion

ACTIVATE SLOW-MOTION

PLAYBACK

1 Turn the TIME SCAN SHUTTLE ring to the left or press PUSH JOG% during playback to decrease speed in the forward direction. To play in reverse slow-motion (and in reverse play mode), continue to turn the TIME SCAN SHUTTLE ring to the left or press PUSH JOG Þafter selecting all the forward direction slow-motion modes.

OR

During still picture, turn the TIME SCAN SHUTTLE ring to the right for forward slow motion, or to the left for reverse slow motion.

OR

During still picture, press and hold PAUSE for 2 seconds, then release. Press and release again to return to still picture.

OR

During still picture, press and hold PUSH JOG % or %.

Release to return to still picture.

To resume normal playback, press PLAY.

Image 13
Contents HR-DD845EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Basic Connections Check ContentsSituate Recorder Connect Recorder to MainsBack of Recorder TV Aerial Cable not providedWith RF Connection Video Channel SetExit Video Channel SET Mode Access Video Channel SET ModeSET Video Channel With AV ConnectionPerform Auto SET UP Auto Set UpIf both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelMake List of Stored Station Names Preset Positions Video Plus+ SetupGuide Program Number Set When Using a Satellite Receiver And/Or Cable System Confirm Preset Position NumberClose Menu Press MenuPlayback BasicActivate HIGH-SPEED Search Playback FeaturesPause During Playback Activate SLOW-MOTION PlaybackOverride Automatic Tracking Adjust TrackingManually Return to AutomaticActivate Index Search Activate 3R PictureActivate Instant Review SET Counter MemorySpatializer Activate SpatializerSoundtrack Selection During PlaybackStop Scene Finder Activate Scene FinderActivate Repeat TimeScan Audio signal during TimeScanVariable-Speed Search/ Reverse Play TimeScan Audio TimeScanSpeed SP Speed LP Audio output Basic Recording Recording Features Recording S.T. Picture SystemDisplay Panel Indication Cord PlaybackPDC Recording Video Plus+ Timer RecordingPress Prog If your recorder receives Satellite Receiver UsersPress OK after entering Enter Programme Regular Timer ProgrammingStart Time TimeReturn to Normal Timer ModeScreen Engage RECORDER’SCheck And Cancel Programmes Access ProgrammeTimer Warning Revise ProgrammeTimer Access Main Menu ScreenAuto Timer Auto SP/LP TimerEdit To Or From Another Video Recorder SET Recording DECK’S Input ModeMake Connections Start Source PlayerEdit From a Camcorder SET RECORDER’S Input ModeStart Camcorder Start RecorderAudio Dubbing Mains outlet Speaker Television Connection To Stereo SystemSatellite Receiver Unit Connection To a Satellite ReceiverPin AV input connectors Scart Aerial connector ENABLE/DISABLE ON-SCREEN Display Access Main MenuTurn on the Recorder On-Screen DispiayRE-SUPPLY Power SET A/B Code SwitchControl Your TV Using Additional Buttons TV Multi-brand Remote ControlSET TV Brand Code TRY Operating TVSET Satellite Receiver Brand Code Satellite Receiver Multi Brand Remote ControlTRY Operating Satellite Receiver Perform Auto Channel SET Auto Channel SetProcedures Preset positions PRStations your recorder Located appear on aManual Channel Set Access ConfirmationSelect Position Input ChannelDelete Channel Select ItemClose Confirmation Select NEW PositionSelect NEW Station Switch StationsSelect Station Name Character Enter NEW CharacterFine-Tuning Channels Already Stored Perform TuningSelect Channel to FINE-TUNETV Station And ID List TV Station Channel Number Guide Turn the Recorder on Clock SetPreparation SET Clock PresetSET Date and Time SET Just ClockIf you are using the AV connection Panel with Auto Timer set to OFF Indicator offBack ClearCamcorder recording is not Camcorder has not been Timer againÄ remain lit on the display panel. Is there Problem? Questions and AnswersMaximum recording time SpecificationsIndex Spatializer Button enables/disables Spatializer. pgEP is for Ntsc Playback only ANT. in Connector enables connection of aerial. pgRemote Control How To Use Installing BatteriesEMO Memo Victor Company of JAPAN, Limited