JVC HR-DD845EK setup guide Recording Features

Page 21

Recording

Features

COUNTER RESET
	q
PROG	RECORD
TV

DISPLAY

2

1 2 3

4

5

6

7 8 9

21

Record One Programme While Watching Another

SELECT PRESET TO WATCH

1 Once recording is in progress, all you need to do is to set the preset controls on the TV for the station you wish to view.

●The programme selected with the TV’s preset controls appears on the TV screen while the one selected with the recorder's TV PROG buttons is recorded on the tape.

Elapsed Recording Time

Indication

You can check the exact time of a recording.

SET COUNTER DISPLAY

1 Press DISPLAY until a counter reading appears on the dispay panel.

RESET COUNTER

2 Press C. (COUNTER) RESET before starting recording or playback.

●The counter is reset to “0:00:00” and shows the exact elapsed time as the tape runs.

C.RESET

04

TV PROG

3

Instant Timer Recording (ITR)

This easy method lets you record for from 30 minutes to 6 hours (selectable in 30-min. increments), and shuts the recorder off after recording is finished.

START RECORDING

1 Press RECORD on the recorder.

ENGAGE ITR MODE

2 Press RECORD again. "" blinks and 0:30 appears on the front display panel.

Tape Remaining Time

DISPLAY REMAINING TIME

1 Press DISPLAY until the time remaining on the tape appears.

●By pressing the DISPLAY button, you can change the display to show the counter reading, preset position, clock time* or tape remaining time.

*Preset position is not displayed during playback.

NOTE:

Depending on the type of tape used, there may be times when the tape remaining time reading may not appear right away, or is not correct. "- - : - -" may sometimes appear, or the display may blink on occasion.

SET RECORDING

DURATION

3 If you want to record for more than 30 minutes, press RECORD to extend the time. Each press extends recording time by 30 minutes.

NOTE:

You can only perform ITR using the RECORD button on the recorder's front panel.

Image 21

Contents HR-DD845EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Basic Connections Check ContentsSituate Recorder Connect Recorder to MainsBack of Recorder TV Aerial Cable not providedWith RF Connection Video Channel SetExit Video Channel SET Mode Access Video Channel SET ModeSET Video Channel With AV ConnectionPerform Auto SET UP Auto Set UpIf both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelVideo Plus+ Setup Make List of Stored Station Names Preset PositionsGuide Program Number Set When Using a Satellite Receiver And/Or Cable System Confirm Preset Position NumberClose Menu Press MenuPlayback BasicActivate HIGH-SPEED Search Playback FeaturesPause During Playback Activate SLOW-MOTION PlaybackOverride Automatic Tracking Adjust TrackingManually Return to AutomaticActivate Index Search Activate 3R PictureActivate Instant Review SET Counter MemorySpatializer Activate SpatializerSoundtrack Selection During PlaybackActivate Scene Finder Stop Scene FinderActivate Repeat Audio signal during TimeScan TimeScanVariable-Speed Search/ Reverse Play TimeScan TimeScan AudioSpeed SP Speed LP Audio output Basic Recording Recording Features S.T. Picture System RecordingDisplay Panel Indication Cord PlaybackVideo Plus+ Timer Recording PDC RecordingPress Prog Satellite Receiver Users If your recorder receivesPress OK after entering Enter Programme Regular Timer ProgrammingStart Time TimeReturn to Normal Timer ModeScreen Engage RECORDER’SCheck And Cancel Programmes Access ProgrammeTimer Warning Revise ProgrammeTimer Access Main Menu ScreenAuto Timer Auto SP/LP TimerEdit To Or From Another Video Recorder SET Recording DECK’S Input ModeMake Connections Start Source PlayerEdit From a Camcorder SET RECORDER’S Input ModeStart Camcorder Start RecorderAudio Dubbing Mains outlet Speaker Television Connection To Stereo SystemSatellite Receiver Unit Connection To a Satellite ReceiverPin AV input connectors Scart Aerial connector ENABLE/DISABLE ON-SCREEN Display Access Main MenuTurn on the Recorder On-Screen DispiayRE-SUPPLY Power SET A/B Code SwitchControl Your TV Using Additional Buttons TV Multi-brand Remote ControlSET TV Brand Code TRY Operating TVSatellite Receiver Multi Brand Remote Control SET Satellite Receiver Brand CodeTRY Operating Satellite Receiver Perform Auto Channel SET Auto Channel SetProcedures Preset positions PRStations your recorder Located appear on aManual Channel Set Access ConfirmationSelect Position Input ChannelDelete Channel Select ItemClose Confirmation Select NEW PositionSelect NEW Station Switch StationsSelect Station Name Character Enter NEW CharacterFine-Tuning Channels Already Stored Perform TuningSelect Channel to FINE-TUNETV Station And ID List TV Station Channel Number Guide Clock Set Turn the Recorder onPreparation SET Clock PresetSET Date and Time SET Just ClockIf you are using the AV connection Panel with Auto Timer set to OFF Indicator offBack ClearCamcorder recording is not Camcorder has not been Timer againÄ remain lit on the display panel. Is there Problem? Questions and AnswersMaximum recording time SpecificationsIndex Spatializer Button enables/disables Spatializer. pgEP is for Ntsc Playback only ANT. in Connector enables connection of aerial. pgRemote Control How To Use Installing BatteriesEMO Memo Victor Company of JAPAN, Limited