JVC HR-DD855EK setup guide Video Channel Set, Access Video Channel SET Mode, SET Video Channel

Page 40

40SUBSIDIARYSETTINGS

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

STOP

IMPORTANT

Perform the following steps only if —

Video Channel Set has not been done correctly by the Auto Set Up function (pg. 6).

interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

you change the connection between your recorder and TV from RF connection to AV connection, or vice versa.

If you have connected the video recorder to your TV via both an RF cable and a 21-pin SCART cable (AV connection), you do not need the video channel so you have to set the video channel to off. Go to "With AV Connection" below.

If you have connected the video recorder to your TV via an RF cable only (RF connection), you have to set the correct video channel Go to "With RF Connection" on page 41.

–:–

With AV Connection

Before performing the following procedure, make sure that:

the mains power cord is plugged into the mains outlet.

the video recorder is turned off and there is no cassette inserted in the recorder.

batteries have been installed in the remote control.

1 2 3

4 5 6

7 8 9

0

1

2

4

TV PROG

OK

ACCESS VIDEO CHANNEL SET MODE

1

Press and hold down STOP on the recorder until the

display panel shows the following.

 

 

 

 

 

 

2

SET VIDEO CHANNEL

Press TV PROG – until the display panel shows

"OUT– –".

 

 

 

 

 

 

 

 

Now the video channel is set to off.

EXIT VIDEO CHANNEL SET MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to its AV mode. Refer to the instructions supplied with your TV set for how to do this.

Image 40
Contents HR-DD855EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of TV TV Aerial Cable not providedMains outlet Back of RecorderYour TV via both an RF cable and a 21-pin Go to itemIf auto channel set has succeeded but auto clock set has not Playback Load a CassettePoint Start PlaybackActivate FRAME-BY-FRAME Playback Pause During PlaybackActivate SLOW-MOTION Playback Recording Select Preset to Watch Reset CounterEngage ITR Mode Display Remaining TimeVideo Plus+ Timer Programming Timer Warning PDC RecordingExpress Timer Programming Before performing Express Timer ProgrammingStart Time TimeSET PDC Mode Timer ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes Playback Picture Adjustment Looking For Scene You Want Activate Index SearchSkip Over Unwanted SectionsActivate Instant Review Instant ReViewTimeScan Variable-Speed Search/ Reverse PlayNormal recorder VisibleNoiselessTimeScan Audio TimeScanSpeed SP Speed LP Audio output Turn on the Recorder Playback/ Recording According To Tape Charac- teristicsS.T. Picture System Playback RecordingOr press Record on the recorder Selecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection Type of Broadcast On-screen Display Being ReceivedAccess Main Menu Adjust AudioReturn to Normal Screen Activate SpatializerAerial connector Automatic Satellite Programme RecordingOutdoor Unit Satellite Cable Satellite Receiver UnitEngage Auto Satellite Prog REC Mode Before performing the following stepsTV Multi-brand Remote Control Control Your TV Using Additional ButtonsRemote Con- trol Functions SET TV Brand CodeSET Remote Control Code RE-SUPPLY PowerSET Satellite Receiver Brand Code Operate Satellite ReceiverEdit To Or From Another Video Recorder Input ModeMake Connections SET RECORDER’S Input Mode Edit From a CamcorderStart Camcorder Start RecorderSET Input Mode Reset the CounterInsert Editing Locate END PointStart Editing Engage Insert EditingEND Insert Editing Audio Dubbing Engage Audio DubbingEND Audio Dubbing Start DubbingPlay to resume dubbing Access Main Menu Screen Access Mode SET ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto SP→LP Timer Auto TimerActivate Repeat Repeat PlaybackNext Function Memory Ntsc PlaybackConnection To Stereo System Audio Cable not provided Speaker Mains outletAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelTest Signal With RF ConnectionTuner Set Auto Channel SetScreen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Fine-Tuning Channels Already Stored Change Station Preset PositionDelete a Channel Access Manual Channel SET Screen Select NEW StationClose Confirmation Select Station Name CharacterTV Station And ID List Channel Islands TV Station Channel Number GuideWinter Hill Clock Set Just ClockNumber Video Plus+ SetupGuide Program Number Set Questions And Answers PlaybackTroubleshooting No power is applied to the recorderConnect the mains power cord Indicator offTimer Recording Won’t stopIndex Front ViewRear View Remote Control How To Use Display Panel Specification S DA4 Double Azimuth helicalHR-DD855EK