JVC HR-DD855EK setup guide Pause During Playback, Activate FRAME-BY-FRAME Playback

Page 9

PLAY	SCAN SHUTTLE
	TIME

PAUSE

JOG

7 8 9

0

4

TV PROG

LAY 1

FF

REW

PAUSE

3

High-Speed (Turbo) Search

ACTIVATE HIGH-SPEED SEARCH

1 During playback or still picture, press FF for forward high-speed search, or REW for reverse high-speed search.

To resume normal playback, press PLAY.

NOTE:

For short searches, press and hold FF or REW for more than 2 seconds during playback or still picture. When released, normal playback resumes.

ATTENTION

●In the high-speed search, still, slow-motion or frame-by- frame playback mode,

●the picture will be distorted.

●noise bars will appear.

●there will be a loss of colour with a tape recorded in LP mode.

●Picture may not appear during high-speed search with a

tape recorded in LP mode.

9

Still Picture/Frame-By-Frame Playback

PAUSE DURING PLAYBACK

1 Press PAUSE. If there is vertical jitter, use the TV PROG buttons to correct the picture.

●During still picture, the sound from the previous

3 seconds (approx.) will be played back repeatedly (provided there was at least 6 seconds of normal playback prior to engaging the still picture mode).

●The "TIME SCAN AUDIO" must be set to "ON", or the sound will not be heard (☞ pg. 21).

ACTIVATE FRAME-BY-FRAME

PLAYBACK

2 Turn the JOG dial to the right for forward frame-by- frame playback, or to the left for reverse frame-by-frame playback.

OR

Press PAUSE. Each time PAUSE is pressed the tape will advance one frame.

OR

Press Þor %. Each time one of these buttons is pressed the tape will move one frame in the direction of the arrow.

To resume normal playback, press PLAY.

Slow Motion

ACTIVATE SLOW-MOTION

PLAYBACK

1 Turn the TIME SCAN SHUTTLE ring to the left or press Þduring playback to decrease speed in the forward direction. To play in reverse slow-motion (and in reverse play mode), continue to turn the TIME SCAN SHUTTLE ring to the left or press Þafter selecting all the forward direction slow-motion modes.

OR

During still picture, turn the TIME SCAN SHUTTLE ring to the right for forward slow motion, or to the left for reverse slow motion.

OR

During still picture, press and hold PAUSE for 2 seconds, then release. Press and release again to return to still picture.

OR

During still picture, press and hold Þor %. Release to return to still picture.

To resume normal playback, press PLAY.

Image 9

Contents HR-DD855EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide TV Aerial Cable not provided Back of TVMains outlet Back of RecorderGo to item Your TV via both an RF cable and a 21-pinIf auto channel set has succeeded but auto clock set has not Load a Cassette PlaybackPoint Start PlaybackPause During Playback Activate FRAME-BY-FRAME PlaybackActivate SLOW-MOTION Playback Recording Reset Counter Select Preset to WatchEngage ITR Mode Display Remaining TimeVideo Plus+ Timer Programming PDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingStart Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes Playback Picture Adjustment Activate Index Search Looking For Scene You WantSkip Over Unwanted SectionsInstant ReView Activate Instant ReviewVariable-Speed Search/ Reverse Play TimeScanNormal recorder VisibleNoiselessTimeScan TimeScan AudioSpeed SP Speed LP Audio output Playback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System Recording PlaybackOr press Record on the recorder Receiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection Type of Broadcast On-screen Display Being ReceivedAdjust Audio Access Main MenuReturn to Normal Screen Activate SpatializerAutomatic Satellite Programme Recording Aerial connectorOutdoor Unit Satellite Cable Satellite Receiver UnitBefore performing the following steps Engage Auto Satellite Prog REC ModeControl Your TV Using Additional Buttons TV Multi-brand Remote ControlRemote Con- trol Functions SET TV Brand CodeRE-SUPPLY Power SET Remote Control CodeSET Satellite Receiver Brand Code Operate Satellite ReceiverInput Mode Edit To Or From Another Video RecorderMake Connections Edit From a Camcorder SET RECORDER’S Input ModeStart Camcorder Start RecorderReset the Counter SET Input ModeInsert Editing Locate END PointEngage Insert Editing Start EditingEND Insert Editing Engage Audio Dubbing Audio DubbingStart Dubbing END Audio DubbingPlay to resume dubbing Access Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto Timer Auto SP→LP TimerRepeat Playback Activate RepeatNext Function Memory Ntsc PlaybackAudio Cable not provided Speaker Mains outlet Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Test SignalAuto Channel Set Tuner SetProcedures Screen preset positionsAfter Scan Completed Is displayed on the screenStoring Channels Manually Change Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Select NEW Station Access Manual Channel SET ScreenClose Confirmation Select Station Name CharacterTV Station And ID List TV Station Channel Number Guide Channel IslandsWinter Hill Just Clock Clock SetVideo Plus+ Setup NumberGuide Program Number Set Playback Questions And AnswersNo power is applied to the recorder TroubleshootingConnect the mains power cord Indicator offWon’t stop Timer RecordingFront View IndexRear View Remote Control How To Use Display Panel DA4 Double Azimuth helical Specification SHR-DD855EK