JVC HR-DD855EK SET Remote Control Code, RE-SUPPLY Power, SET Satellite Receiver Brand Code

Page 29

VCR

 

 

 

 

–:–

 

 

 

 

 

SAT

 

NUMBER "1"

1

2

3

 

 

 

 

2

NUMBER

 

4

5

6

 

 

 

 

"2"

8

9

 

 

7

 

 

NUMBER

 

0

4

 

 

 

 

 

1

STOP

3

TV PROG+/–

Remote A/B Code Switching

The remote control is capable of controlling two JVC video recorders independently; one set to respond to the remote control’s A code control signals and another set to respond to B code control signals. The remote control is preset to send A code signals because your video recorder is initially set to respond to A code signals. You can easily modify your video recorder to respond to B code signals.

REMOVE POWER SUPPLY

1 Unplug the mains power cord from the mains outlet.

SET REMOTE CONTROL

CODE

2 While holding down VCR on the remote control, press the NUMBER key "2" and then press STOP.

RE-SUPPLY POWER

3 Plug the mains power cord back into the mains outlet.

TURN THE RECORDER ON

4 Press on the remote control. The recorder will now only respond to B code signals.

NOTE:

To set the recorder back to respond to A code signals, repeat the same procedure as shown above except pressing NUMBER key "1" instead of "2" in step 2.

29

Satellite Receiver Multi-

Brand Remote Control

Your remote control can operate the basic functions of your satellite receiver set. In addition to JVC satellite receivers, other manufacturer’s satellite receivers can also be controlled.

Before you start . . .

Turn on the satellite receiver using its remote control.

SET SATELLITE RECEIVER

BRAND CODE

1 Refer to the chart below. While holding down SAT on the recorder's remote control, enter your satellite receiver’s brand code using the NUMBER keys, then press STOP.

Check if the satellite receiver's power goes off as it should. If it does, try other operations (step 2)

Once you have set the remote control to operate the satellite receiver, you don't have to repeat this step until you replace your remote control's battteries.

Some satellite receiver brands have more than one code. If the satellite receiver does not function with one code, try entering another.

OPERATE SATELLITE

RECEIVER

2

First, press SAT to set the remote control to satellite

receiver mode, then press the corresponding button:

, TV PROG +/–,NUMBER keys.

For VIDEOWAY or some brands of satellite receiver,

you must press after having pressed the NUMBER keys.

The NUMBER buttons may not function with some satellite receivers.

IMPORTANT

Although the provided remote control unit is compatible with JVC satellite receivers, as well as many other models, it may not work with your satellite receiver, or in some instances, may have limited function capability.

SATELLITE RECEIVER BRAND

CODE

 

 

JVC

13, 14

AMSTRAD

01, 02, 03, 04

GRUNDIG

05, 06

HIRSCHMANN

05

SIEMENS

05

WISI

05

KATHREIN

05, 11, 12

PACE

06, 08

PHILIPS

07

FINLUX

09

ITT

09

NOKIA

09

SALORA

09

RFT

10

SKYMASTER

10

MASPRO

11

BT

13

PANASONIC

15

JERROLD

16

VIDEOWAY

17

 

 

Image 29
Contents HR-DD855EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide TV Aerial Cable not provided Back of TVMains outlet Back of RecorderGo to item Your TV via both an RF cable and a 21-pinIf auto channel set has succeeded but auto clock set has not Load a Cassette PlaybackPoint Start PlaybackActivate SLOW-MOTION Playback Pause During PlaybackActivate FRAME-BY-FRAME Playback Recording Reset Counter Select Preset to WatchEngage ITR Mode Display Remaining TimeVideo Plus+ Timer Programming PDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingStart Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes Playback Picture Adjustment Activate Index Search Looking For Scene You WantSkip Over Unwanted SectionsInstant ReView Activate Instant ReviewVariable-Speed Search/ Reverse Play TimeScanNormal recorder VisibleNoiselessSpeed SP Speed LP Audio output TimeScanTimeScan Audio S.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Receiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection Type of Broadcast On-screen Display Being ReceivedAdjust Audio Access Main MenuReturn to Normal Screen Activate SpatializerAutomatic Satellite Programme Recording Aerial connectorOutdoor Unit Satellite Cable Satellite Receiver UnitBefore performing the following steps Engage Auto Satellite Prog REC ModeControl Your TV Using Additional Buttons TV Multi-brand Remote ControlRemote Con- trol Functions SET TV Brand CodeRE-SUPPLY Power SET Remote Control CodeSET Satellite Receiver Brand Code Operate Satellite ReceiverMake Connections Input ModeEdit To Or From Another Video Recorder Edit From a Camcorder SET RECORDER’S Input ModeStart Camcorder Start RecorderReset the Counter SET Input ModeInsert Editing Locate END PointEND Insert Editing Engage Insert EditingStart Editing Engage Audio Dubbing Audio DubbingPlay to resume dubbing Start DubbingEND Audio Dubbing Access Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto Timer Auto SP→LP TimerRepeat Playback Activate RepeatNext Function Memory Ntsc PlaybackAudio Cable not provided Speaker Mains outlet Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Test SignalAuto Channel Set Tuner SetProcedures Screen preset positionsAfter Scan Completed Is displayed on the screenStoring Channels Manually Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Select NEW Station Access Manual Channel SET ScreenClose Confirmation Select Station Name CharacterTV Station And ID List Winter Hill TV Station Channel Number GuideChannel Islands Just Clock Clock SetGuide Program Number Set Video Plus+ SetupNumber Playback Questions And AnswersNo power is applied to the recorder TroubleshootingConnect the mains power cord Indicator offWon’t stop Timer RecordingFront View IndexRear View Remote Control How To Use Display Panel DA4 Double Azimuth helical Specification SHR-DD855EK