JVC BR-DV600EA, BR-DV600UA manual Menu Switches, Menu switch details

Page 12

4 MENU SWITCHES

4 MENU SWITCHES

4-2 Menu switch details

For switch setting procedures, refer to “Menu switch setting

procedure”.

q:

Factory setting

(00): The number in the bracket shows the set value on the

 

counter display.

002OPERATION LOCK

Details: Switches the operation lock ON/OFF. Setting:

qOFF (00): The operation lock is OFF: all operations are enabled.

ON (01): The operation lock is ON: all controls are disabled except for the [MENU] button.

003SYNC SELECT

Details: Selects the sync signal during play. Setting:

EXTERNAL (01): Synchronizes with the signal input

to the [SYNC IN] connector. qAUTO (03): Switches the synchronization automatically depending on whether or not a signal is input to the [SYNC IN] connector. For details, refer to page 12.

050REMOTE SELECT

Details: Selects the remote controller connected to the [REMOTE] connector on the rear panel. When the optional SA-K46 RS-232C interface board is installed at the [REMOTE 1] connector, some setting indications will change.

Setting:

IEEE 1394 (01): Allows control of this unit with the controller connected to the [DV IN/ OUT] connector. RS422A (04): Allows control of this unit with the controller connected to the [REMOTE 1] connector. IEEE 1394 + RS422A (05): Allows control of this unit with the controllers connected to the [DV IN/OUT] and [REMOTE 1] connectors. JVC BUS (08): Allows control of this unit with the controller connected to the [REMOTE 2] connector. JVC BUS + IEEE 1394 (09): Allows control of this unit with the controllers connected to the [REMOTE 2] and [DV IN/ OUT] connectors. JVC BUS + RS422A (12): Allows control of this unit with the controllers connected to the [REMOTE 2] and [REMOTE 1] connectors. qJVC BUS + RS422A + 1394 (13): Allows control of this unit with the controllers connected to the [REMOTE 2], [REMOTE 1] and [DV IN/OUT] connectors.

(When the optional SA-K46 RS-232C interface board is installed)

EEE1394 (01): Allows control of this unit with the controller connected to the [DV IN/

RS232C (02):

OUT] connector.

Allows control of this unit with the

 

controller connected to the

 

[REMOTE 1] connector.

IEEE 1394 + RS232C (03): Allows control of this

 

unit with the controllers connected

 

o the [DV IN/OUT] and [REMOTE 1]

JVC BUS (08):

connectors.

Allows control of this unit with the

 

controller connected to the

 

[REMOTE 2] connector.

JVC BUS + IEEE 1394 (09): Allows control of this

 

unit with the controllers connected

 

to the [REMOTE 2] and [DV IN/

 

OUT] connectors.

JVC BUS + RS232C (10): Allows control of this unit

 

with the controllers connected to

 

the [REMOTE 2] and [REMOTE 1]

 

connectors.

qJVC BUS + RS232C + 1394 (11): Allows control of

 

this unit with the controllers

 

connected to the [REMOTE 2],

 

[REMOTE 1] and [DV IN/OUT]

 

connectors.

052STEP SLOW MODE

Details: Selects the advance amount in the STILL mode.

Setting:

FIELD(00): Field-by-field advance. qFRAME (01): Frame-by-frame advance.

053STOP FUNC. AT SEARCH

Details: Selects the operation when the STOP command is received by RS-422A during SEARCH mode.

Setting:

qSTOP(00): When the command is received, the stop mode is entered. Normally, use this setting.

STILL(01): When the command is received, the pause mode is entered.

Use this setting when CUE operation fails to work normally when the “STOP” setting is selected.

054SLIDE SW FUNCTION

Details: Use this to select the function of the [VIDEO INPUT/AUDIO MONITOR] switch.

Setting:

AUDIO (00) : The [AUDIO MONITOR OUT] connector output can be switched with the [VIDEO INPUT/AUDIO MONITOR] switch.

qVIDEO (01) : The [VIDEO INPUT/AUDIO MONITOR] switch functions as [VIDEO INPUT] switch.

q:

Factory setting

(00): The number in the bracket shows the set value

 

on the counter display.

108VIDEO INPUT SELECT

Details: Use this to select the input video signal when No. 054 <SLIDE SW FUNCTION> menu switch is set to “AUDIO (00)”. When the No. 054 menu switch is set to “VIDEO”, the [VIDEO INPUT] switch on the front panel is enabled.

Setting:

qLINE (00):

Selects video signals input to

Y/C (01):

the [LINE IN] connector.

Selects video signals input to

 

the [Y/C IN] connector.

COMPONENT (02): Selects video signals input to

 

the [COMPONENT IN]

IEEE 1394 (03):

connector.

Selects video and audio signals

 

input to the [DV IN/OUT]

 

connector. In this case, analog

 

audio signals are not input.

109VIDEO INPUT2

Details: Use this to select the type of input video signals when the [VIDEO INPUT] switch is set to “Y/C (CPN)”. This switch is effective when the No. 054 <SLIDE SW FUNCTION> is set to “VIDEO (01)”.

Setting:

qY/C (00):

Selects video signals input to

 

the [Y/C IN] connector.

COMPONENT (01): Selects video signals input to

 

the [COMPONENT IN]

 

connectors.

125SETUP (U MODEL)

Details: Sets whether or not the setup is applied to the analog video signals (composite, Y/C, component).

Setting:

OFF (00): Does not apply the setup.

qON (01): Applies the setup. Set to this position to play back a tape recorded on the GY-DV500.

Notes:

•This setting affects recording and playback of analog video signals.

•Picture hue and brightness can be affected if dubbing is repeated without applying a setup suitable to video signals.

•When video signals are input from the [DV IN] connector, setup signals will not be provided to the DV and analog outputs even if the No. 125 <SETUP> menu switch is set to “ON”.

If you would like to provide set up signals when playback, set menu switch No.108 [VIDEO INPUT SELECT] to LINE, Y/C or COMPONENT position

(except IEEE 1394).

 See “Recording preparation” on page 26.

211AUDIO MONITOR

Details: Use this to select which audio channel to output from the [AUDIO MONITOR OUT] connector when the No. 054 <SLIDE SW FUNCTION> menu switch is set to “VIDEO INPUT (01)”.

Setting:

L:Outputs CH1/3 audio signals.

R:Outputs CH2/4 audio signals.

qMIX: Outputs CH1/3 and CH2/4 audio signals.

212AUDIO OUT AT SEARCH

Details: Selects whether or not audio is output to the [AUDIO OUT] and [AUDIO MONITOR OUT] connectors and headphones jack during search.

Setting:

OFF (00): No output. qON (01): Audio is output.

214V. FADE

Details: Switches the V. fade function ON/OFF. V.fade reduces audio noise at the tag recording during playback.

Setting:

OFF (00): The V. fade function is not activated. qON (01): Activates the V. fade function.

245SAMPLING RATE

Details: Selects the sampling rate frequency when recording audio digitally.

Setting:

32K (00): Records signals at a 32 kHz sampling frequency. Set to this position for audio dubbing on CH3 and CH4.

q48K (01): Records signals at a 48 kHz sampling frequency. Audio dubbing is not possible with this setting.

311AUTO PLAY

Details: Selects whether or not playback starts automatically after the tape is rewound to the beginning.

Setting:

qSHORT FF (00): The tape stops after short FF.

PLAY (01):

Auto play does not start.

Auto play starts. Repeat playback

 

is available when No. 312 <AUTO

 

REW> menu switch is set to “ON”.

20

→

For servicing

See the BR-DV600’s service manual page 1-19, “1.11

 

21

SET UP SW”

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Thank you for purchasing this JVC product Before operating this unit, please readInstructions carefully to ensure Best possible performance For Customer UsePort Cable LengthMeters Safety Precautions For Your Safety AustraliaThis unit should be used with 120 V AC only Mains Supply AC 230 V `Major features MaintenanceIntroduction Precautions Precautions for use of head cleaning tapeIntroduction # Y/C in connector Rear panelCONTROLS, Connectors and Displays On-screen displayLCD display Slave NDF HoldReference sync signal ConnectionsAudio system connections OutputsRemote connector Power socketsOther connections Editing system examplesEdit adjust setting BR-DV600UA/EABR-DV600UA Menu Switches Menu switch organizationMenu switch group select screen Menu switch setting screenMenu Switches Menu switch detailsEdit Adjust Auto REW AT TimerBattery Select Remote FF/REW ModePreparation PreparationRecording RecordingPlayback Repeat play Playback preparationExternal TIMER-START Function PresetTime Code DisplayTime Code Super Scene Finder Function PlaybackPlayback time code Backup Recording Function 12 RS-232C Interface Command tables12-2 RS-232C specifications 12-3 RS-232C commandsVCR operation commands 12 RS-232C InterfaceInformation gathering sense commands Setting preset commandsCommands Description Contents of Status Sense Contents of JVC Status SenseError-related commands Menu switch setting command Menu switch check commandED Memory SW Preset ComponentTroubleshooting Operation SolutionDEW indicator lights Counter displaySpecifications Other problemsOptional equipment

BR-DV600EA, BR-DV600UA specifications

The JVC BR-DV600UA and BR-DV600EA are professional digital video recorders that have gained recognition in the broadcasting and media production industries due to their advanced features and reliability. These models are tailored for video professionals who require high-quality video capture and playback capabilities.

One of the standout features of the BR-DV600 series is its compatibility with various formats, including DVCAM, DVCPRO, and standard DV, making it an adaptable option for many users. The ability to record in multiple formats allows for flexibility in production workflows, accommodating diverse client needs and project requirements.

The BR-DV600UA and BR-DV600EA are equipped with robust transport mechanisms, ensuring stable and accurate playback. This reliability is crucial in professional settings where quality cannot be compromised. The units are designed to withstand the rigors of daily use, featuring durable construction that protects the internal components.

A notable technology integrated into these recorders is JVC's innovative digital signal processing, which enhances the overall video quality. This technology ensures improved color reproduction and finer detail, resulting in footage that meets the high standards of professional productions. Furthermore, the devices support real-time editing capabilities, which allow for seamless transitions and effects during the recording process, thus expediting post-production.

Another key characteristic of the BR-DV600 series is its comprehensive connectivity options. The recorders come equipped with multiple input and output interfaces, including FireWire (IEEE 1394), composite, and SDI connections. This versatility enables users to integrate the units into various production environments easily, whether for live events, studio recordings, or field productions.

User-friendly operational design is also evident in these models. The intuitive interface, clear LCD displays, and accessible controls facilitate ease of use, allowing operators to focus on their craft without being hindered by complicated setups. The built-in editing functions further enhance usability, enabling quick adjustments and refinements on the fly.

In summary, the JVC BR-DV600UA and BR-DV600EA digital video recorders stand out in the professional video market due to their format versatility, advanced digital processing technologies, reliable construction, and user-friendly designs. These features collectively make them an excellent choice for videographers, broadcasters, and production companies seeking dependable and high-quality recording solutions.
Top Page Image Contents