Magnavox VRU344AT manual Setting Up VCR, Plus+ contd, Up/Down, Guide Channel SET

24

Setting Up VCR

Now, compare the channel numbers you have written in the GUIDE CH. and USER CH. columns. You'll notice that some stations have guide and user chan- nel numbers that are the same, and other stations have channel numbers that do not match. Where the channel numbers DO NOT match, you must tell the VCR the guide and user channel numbers according to the following steps.

•Make each entry within 60 seconds of the previous entry.

3

Plus+ (cont'd)

Press the Number 1 button so your VCR will memorize the guide channel and user channel numbers you have selected. Or, press the Number 2 but- ton to quit and select another pair of numbers.

GUIDE CH.28

USERCH. 04 1 MEMORIZE

I TO SELECTPUSH NUMBER 2 SELECTANOTHER CH,

_._--GUIDE CHANNEL SET 1 TO CORRECT PUSH CLEAR

k. TO ENDPUSH EXIT

7

CHANNEL

(Up/Down)

]---- Buttons

Number Buttons MENU Button

--CLEAR Button

STATUS/EXIT Button

Press the MENU button, then press the Number 2 button to select VCR SET UP.

Ii SELECT PUSH NO. SHOWN_

1 NORMALPLAY ON [

2 REPEATPLAY[

3 ON SCREEN MODE

4 LANGUAGE

5 GUIDECHANNEL SET

6 GUIDECHANNELMAP )

END PUSH EXIT J

4

Press the Number 5 button to select

GUIDE CHANNEL SET.

fGUIDE CHANNEL SET

GUIDE CI'_:::-:

USER CH. ":'-

ISELECT GUIDE ell.NO.

END PUSH EXIT

5

Look at the boxes you filled in on pages 22-23. For stations whose guide channels and user channels are not the same, press two Number buttons for the guide channel and two Number buttons for the user channel.

• Always enter a "0" before single

Repeat steps 5 and 6 for all the stations on your list which have different guide channel and user channel numbers.

8

Press the STATUS/EXIT button to exit.

9

• To correct a guide channel number:

1. Repeat

steps

3

-

4 on this

page.

2. At step

5,

enter

the

incorrect

guide

To confirm the guide channel and user

channel

number for both the guide

channel numbers you have selected,

channel

and

the

user

channel.

Press

press the MENU button to bring up the

the Number

1 button.

Press

the STA-

main menu display. Then press the

TUS/EXIT

button

to exit.

+

Number 2 button

to select VCR SET

3. Repeat

steps

3 -

6 again,

this time

UP. Finally, press

the Number 6 button

entering

the

correct

guide

channel

to select GUIDE CHANNEL MAP. A

and

user channel. Press the STA-

list of guide channel and user channel

TUS/EXIT

button

to exit.

•

To correct a user channel number:

numbers memorized by the VCR will

1. Repeat steps 3 - 4 on this page.

appear on-screen.

If there are more

2. At step 5, enter the correct guide

than 10 pairs of numbers, press the

channel and user channel numbers.

Number 1 button to view another

Press

the Number 1 button. Press the

screen of numbers. Make sure these

STATUS/EXIT

button to exit.

numbers correspond to the boxes you

•

To cancel a pair of numbers:

filled in in step I. Then press the

1. Follow step 9 to display the guide

STATUS/EXIT button to exit.

channel

map.

2. Press the CLEAR button. A pair of

digit channels.

• To select line input for the user chan-

nel, press 0, 0. AUX will appear on-

screen.

SELECT USER CH. NO.

GUIDE CH.

USER CH._" _,_

GUIDE : USERGUIDE: USER I

1 :AUX	2:2
3:3	4:4	]
6:6	7:7
g : 9	10:10	/
23:5	91:8	/
TO¢J_3EL PUSH_]
NEXT=I	END=EXITJ

numbers will flash.

3. Press the CHANNEL (Up/Down) but- tons until the pair of numbers you wish to cancel is flashing.

4.Press the CLEAR button again. The pair of numbers that was flashing will

disappear.

5.Press the STATUS/EXIT button to

exit.