Magnavox VRU344AT manual Timer Recording With VCR Plus, Number, Buttons

25

Timer Recording With VCR Plus

Remote	Control
POWER
Button	VCR
t_®-¢	PLUS+/
Number	-ENTER
Buttons
	Button
STATUS/
EXIT	MENU
Button	Button
	_CLEAR
	Button

oo*o*ololoaeoooooo_olool oooooo OOOOIllOGOOOQ

• If you make a mistake while you	are
entering the VCR Plus+ number	of a
program, press the CLEAR button until

Follow the steps below to program a timer recording using VCR Plus+ num- bers. Before you begin, make sure:

•Channels have been programmed.

•The clock has been set.

•There is a tape in the VCR. Make sure the tape's record tab is intact and the tape is long enough to record the pro- gram(s).

•The VCR is in VCR position.

•You have selected CABLE TV or TV at the TUNER SET UP menu.

•You have completed the steps on

pages 22-24.

You must do each step within 60 sec- onds of completing the previous step.

If you don't, you will have to start again at step 1.

Press the VCR PLUS+/ENTER button on the remote control. The on-screen display shown below will appear.

_l

Press the Number l button to record in SP speed, press the Number 2 button to

record in LP speed, or press the Number 3 button to record in SLP

speed. For details, see page five. You cannot use the (Tape) SPEED button at this time.

TIME ON	10:30 PM
TIME OFF	11:30 PM
EL	9
PRoGETIME PROGRAM		1
END PUSH EXff		"

Jill

Press the STATUS/EXIT button. PRO-

GRAM WAS COMPLETED / PLEASE TURN OFF VCR FOR

TIMER RECORDING should appear on the screen. After three seconds, the-

on-screen display will disappear.

the cursor is flashing on the item you

want to correct. Then enter the correct

number.

• If CODE ERROR flashes after you enter

the VCR Plus+ number and press the

VCR PLUS+/ENTER button, the number

you entered was incorrect (for example,

too short). If this happens, enter the

correct number.

• CLASH ma_flash on the screen at step

2. This means that the timer recording

you just programmed and another timer recocding overlap, and thus the current timer recording will not be carried out.

•To quit VCR Plus+ programming at any time, press the STATUS/EXIT button. The display will disappear from the TV screen.

•If the preset time for a timer recording comes up during an OTR, the OTR has

priority.

•To stop a started timer recording, press the STOP/EJECT button on the VCR.

•If the power fails for more than one minute, programmed timer recordings will be lost. When you use the VCR with the auto clock function turned OFF, repeat the steps on page 10 before re-programming the timer recordings.

•To cancel a Timer Recording with VCR Plus+, follow the steps for Checking or Clearing Timer Recordings on page 20.

See page 35for more notes.

LUScoo_._ .... -j

FND PUSH EXIT

2

Use the Number buttons to enter the VCR Plus+ number of the program you wish to record (this number is dif- ferent for every program, and it can be four to eight digits long). Finally, press the VCR PLUS+/ENTER button.

,_VCR PLUS+ PROG.J

PLUS CODE: 132B_:: ._::.-

TO SET PUSH VCR +

TO CORRECT PUSH CLEAR

END PUSH EXIT

3

To record the program once, press the Number 1 button to select ONCE. To

•record the same program every day from Monday through Friday, press the Number 2 button to select DAILY. To

record the same program every week on the same day (such as every Saturday),

i press the Number 3 button to select

6

To program additional timer recordings with VCR Plus+, press the VCR PLUS+!ENTER button and repeat steps 2- 5. When you are finished, go to step 7.

7

Turn off the VCR power. The Timer light will appear. The Timer light will flash if there is not a tape in the VCR. The VCR must be turned off for a timer recording to take place. If you

forget to turn the VCR off, PLEASE TURN OFF VCR FOR TIMER

RECORDING flashes on your TV screen two minutes before a timer

recording starts. You can remove it by )ressing the CLEAR button.

The VCR must be off for a timer recording

to take place! Make sure there

is a taoe in the