Emerson EV477 owner manual Servicing, Damage Requiring Service, Replacement Parts, Safety Check

Page 4

IMPORTANT SAFEGUARDS (CONTINUED)

18.SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19.DAMAGE REQUIRING SERVICE

Unplug the unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power-supply cord or plug is damaged.

b.If liquid has been spilled, or objects have fallen into the unit.

c.If the unit has been exposed to rain or water.

d.If the unit does not operate normally by following the operating instructions. Adjust only those con trols that are covered by the operating instructions, as an adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its nor- mal operation.

e.If the unit has been dropped or the cabinet has been damaged.

f.When the unit exhibits a distinct change in performance-this indicates a need for service.

20.REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

21.SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.

22.WALL OR CEILING MOUNTING

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

23.HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

24.NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con- nected to the grounding system of the building, as close to the point of cable entry as practical.

EXAMPLE OF ANTENNA

GROUNDING

GROUND CLAMP

ANTENNA LEAD

IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

ELECTRIC

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

SERVICE

 

EQUIPMENT

 

 

GROUND CLAMPS

 

POWER SERVICE GROUNDING

 

ELECTRODE SYSTEM

NEC - NATIONAL ELECTRICAL CODE

(NEC ART 250 PART H)

3

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Remote Control Important Safeguards Power Sources POWER-CORD ProtectionPower Lines VentilationDamage Requiring Service Replacement PartsSafety Check ServicingFeatures Table of Contents Front of VCR Location of ControlsRear of VCR Power Record VCR Timer Display PanelStop KEY CM. Skip KEY Number Keys Remote ControlInput KEY TV/VCR KEY HOW to Install Batteries HOW to USE the Remote ControlBattery Precautions Connections Separate VHF and UHF AntennasVCR to TV Connection VCR to Cable System Connection Allows PreventsCatv Incoming Cable Converter Descrambler Recording scrambled channels Video Cassette LoadingUnloading VCR will turn on automaticallyTypes of Video Cassette Setting the Video ChannelTo Prevent Accidental Erasure Basic Playback Special Operations Clear Display O.S.DChild Lock CM. SkipMenu Operation TV/VCR Menu ScreenSetting the Clock SET DAYLIGHT-SAVING Time Press the Menu key to save the selectings you Have madeAuto Channel Search Setting TV ChannelsTo SET the Cable BOX To Delete a Channel Signal Type SelectionTo ADD a Channel Recording TV Programs To Watch & Record the Same ChannelTo Pause PreparationTo Stop Recording To Watch ONE Channel and Record AnotherTo Record a Cable Program Before Setting OTR Make Sure That ONE Touch Timer Recording OTROperation Tape is long enough to record the desired program ON-SCREEN Timer ProgrammingExample Press the Menu key on the remote control. Press the number key 1 to enter the Timer Recording modeMenu screen appears ChannelPress the number keys to set the Hour AutomaticallyPress the number keys to set the Month Then Year 00 will be set automaticallyChecking Timer Programs Cancelling and Reviewing Timer ProgramsWhen the program contents to be erased is dis Program screen will appearTimer Programming Error Indicator Overlapping Timer RecordingsDiagram below illustrates this point Language Selection Selecting the ON-SCREEN Display LanguageAppear Auto Play Setting UP the VCRAuto TV/VCR VHS Index Search System Viss Automatic Recording of the Index MarkGO -TO Search Tape CounterTape counter is displayed on the screen VCR will search for the time counter you wantDuplicating a Video Tape Connection to Another VCRConnection to a Camcorder Connection to a Audio SystemPlayback VCR Speaking the Language a Glossary of Terms Troubleshooting Guide Accessories TimerVideo Head Cleaning Video Head CleaningVideo Head Clogging Specifications Emerson Radio Corp Limited
Top Page Image Contents