Meridian Audio DVP1500 manual Setup Menu Functions, Set Scanrate

Page 9

SETUP

SETUP MENU FUNCTIONS

Set: SCANRATE

Select the required scanrate by using the right and left arrows. When the desired rate is displayed on the LCD display, press the STORE key on the remote or ENTER on the front panel. The DVP1000 will ask you "Are you sure" and press the STORE/ENTER key again. The scanrate is now selected.

Set: Active Output Analog/Digital (Default)

This must be selected to determine if the Analog (BNC) or Digital (DVI) output is used. Both outputs cannot be used at the same time.

Set: Screen Shape

Wide Screen / 4:3 / Wide 4:3

Note: This sets the processor for the screen shape of the display to be used. If this is not set properly, the aspect ratio selection for the different sources located in the user menu will be incorrect.

•Wide Screen-Choose this when the screen is Widescreen and the projector will provide the anamorphic vertical squeeze.

Example: A 16:9 plasma, a digital or CRT projector set to Anamorphic using a wide angle screen or when using a Panamorph lens, or a 1280x720 digital projector.

•4:3 – Choose this when the projector is 4:3 and the screen is 4:3

Example: using a 1024x768 digital projector on a 4:3 screen.

•Wide 4:3-Choose this when the digital projector operates as 4:3 and the screen is Widescreen. (Not available on units scanning at rates below 720p)

Example: A digital projector that has a 4:3 display chip that locks the aspect ratio when sent the native resolution and then displayed on a wide angle screen.

Output Format (Analog)

RGB (Default) /YPrPb

Note: Selecting RGB means connecting the processor to the display via five wire analog RGBHV. This function is not active when DVI output is selected. DVI is always RGBHV.

Composite Sync on H

On/Off (Default)

Note: this function is not active when YPrPb output is selected.

Horizontal Sync Polarity Negative (Default) / Positive

Changes sync polarity, which may be needed for compatibility with some displays.

Vertical Sync Polarity

Negative (Default) / Positive

Changes sync polarity, which may be needed for compatibility with some displays

Note: Each input on the DVP1500 can be activated or deactivated to simplify operation so unused inputs are not accessed when cycling through the inputs with the remote control.

Set: Video Input

Enabled (Default) /Disabled

Note: Disabling this unused input will remove it from the input menu list.

Set: S-Video Input

Enabled (Default) /Disabled

Note: Disabling this unused input will remove it from the input menu list.

Set: RGB Input

Enabled (Default) /Disabled

Note: Disabling this unused input will remove it from the input menu list.

Set: YCrCb Input

Enabled (Default) /Disabled

Note: Disabling this unused input will remove it from the input menu list.

Set: DVI Input

Enable / Disable

Note: Disabling this unused input will remove it from the input menu list.

Set: Passthru Input

Enabled (Default) /Disabled

Note: Disabling this unused input will remove it from the input menu list.

Set: Passthru Transcode Disable (Default) /Enable

YPrPb HDTV signals via the D15 input or the YPrPb (BNC) inputs can be transcoded to RGB when this feature is enabled.

Set: Component Input Standard

DVD (Default) /Professional (Betacam)

Note: Only use professional setting when using

a device that conforms to SMTPE Betacam levels

Set: RGB Input Sync

Sync-on-Green (Default) /TTL/Video

OSD (On Screen Display)

On (Default) /Off

5

Page 8 Page 10
Image 9
Page 8 Page 10
Contents DVP1500 Setting Display Profiles DVP1500 SetupQuick Start Instructions ConnectionsSafety Precautions Safety PrecautionsImportant Safeguards FCC Information U.S.A. onlyDo not allow any unqualified person to install the unit Table of Contents Installation InstallationConnecting Hdtv Satellite Receivers Setup System Firmware SetupSet Scanrate Setup Menu FunctionsIR Remote OSD Operation On Screen Display OSDIR Remote / OSD Input OSD / Operating InstructionsInput Picture Display Available Patterns RS232 InstructionsOperating Instructions / RS232 RS232 Codes Used for day-to-day operationUSE only by Qualified Technician DVD Operation Commands Help Menus Test Pattern Help MenuRS-232 Ascii SpecificationsDVD Playing recordable CDsMP3 compatibility information Remote Control Number buttons 1-9, 0, +10 Load a disc Press OPEN/CLOSE on the front panelPress Play on the front panel Select the item you want to viewChapter Track Skip Forward When setting up for the first time Press the Power button on the smallPress Setup Press Stop onceDVD Adjusting the Dynamic Range Audio Soundtrack DVD Page DVD S-VIDEO Output is not Available with the NRS-DCS DVD Settings English Press Audio repeatedly to select the desired languageFrançais English Deutsch Italiano Español DVD Language code list can be found on When Other is selectedUse the cursor buttons to select Other and press Enter Press Enter to set the new languageEnglish French Chinese German Other Italian Spanish Settings Subtitle LanguageOff Assist Subtitle Selected SubtitlePress Pause 8, STEP/SLOW e or E To return to normal playbackPress Pause 8, STEP/SLOW e or E Press STEP/SLOW e or E When performing a time search Press Search Mode repeatedly to select the type of searchPress Play Super VCD/Video CDNavigate using the following controls Using the MP3 Navigator MP3To cancel A-B repeat play To cancel repeat playPress Random once, then press Enter or Play Press Random twice, then press Enter orTo program a pause in a program Press Enter or PlayTo delete a number To insert a numberDVD/Super VCD/Video CD/CD To confirm the contents of a programPress Program To add to a programPress Program to enter the MP3 Program screen ToNotesconfirm the contents of a programUse the number buttons to enter a three- digit track number To save a program in memory DVDPress Last Memory while in the stop mode Press Last Memory during playLoad a disc that has a Last Memory point memorized DVD DVD DVD Viewing Disc Information DVD DVD Faroudja DVD Using the wrong remote Faroudja Limited Warranty
Top Page Image Contents