Intel PPC-7508F M1 Advanced Bios Features, Bios Features Setup Screen, CPU L1 & L2 Cache

Page 68

Chapter 4 Award BIOS Setup

4-4. THE ADVANCED BIOS FEATURES

Choose the〝ADVANCED BIOS FEATURES〞in the main menu, the screen shown as below.

Phoenix - AwardBIOS CMOS Setup Utility

Advanced BIOS Features

Virus Warning	[Enabled]
CPU L1 & L2 Cache	[Enabled]
CPU L3 Cache	[Enabled]
Quick Power On Self Test	[Enabled]
First Boot Device	[SATA/SCSI]
Second Boot Device	[HDD-0]
Boot Up Floppy Seek	[Enabled]
Boot Up NumLock Status	[On]
Typematic Rate Setting	[Disabled]
x Typematic Rate (Chars/Sec)	6
x Typematic Delay (Msec)	250
Security Option	[Setup]

Item Help

Menu Level ►

↑↓→←: Move Enter: Select	+/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values	F6: Fail-Safe Defaults	F7:Optimized Defaults

BIOS Features Setup Screen

The “BIOS FEATURES SETUP” allow you to configure your system for basic operation. The user can select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security.

A brief introduction of each setting is given below.

Virus Warning:

Allows you to choose the VIRUS warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep.

CPU L1 & L2 CACHE:

This item allows you to enable L1 & L2 cache.

Page: 4-8

PPC-7508F USER′S MANUAL

Image 68

Contents USER’S Manual PPC-7508F Panel PC System FCC Notice Table of Contents Software Utilities Appendix B Technical Summary Introduction System Configuration About this ManualCase Illustration System Specifications Mainboard PROX-7500Display LCD Panel Touch Screen Check the Line Voltage Environmental ConditionsHandling Good CareSystem Configuration Jumper & Connector Quick Reference Table JP8PPC-7508F Connector, Jumper and Component locations Component LocationsHOW to SET the Jumpers Jumpers and CapsJumper Diagrams Jumper Settings PPC-7508F Jumper Illustration COM 1 RI & Voltage Selection Pin ClosedCOM 2 RI & Voltage Selection COM 3 RI & Voltage Selection COM 4 RI & Voltage Selection RS232/422/485 COM2 Selection Default Brightness Voltage SelectionLvds Voltage Selection Lvds Panel Resolution Selection Default Open Cmos Function SelectionReset / NMI Selection NMICpuvcca Voltage Selection CPU Frequency Selection 100 MHzCOM Port Connector RS-232 RS-422 RS-485COM3 COM3 Connector Pin assignments are as follows VGA Connector Lvds Connector Power Connector Hard Disk Drive Connector PIN AssignmentPrinter Connector LAN Connector LAN LED ConnectorKeyboard Connector 25. PS/2 Mouse ConnectorPower LED Connector HDD LED ConnectorPower Button Universal Serial BUS Connector 5VUSB2 Memory Installation Inverter ConnectorPower Module Compact Flash Connector CF1 Compact Flash Connector Pin assignments are as followsPCI-104 Connector PC104PLUS1 PCI-104 Connector Pin assignments are as followsSerial ATA Connector CPU FAN ConnectorSystem FAN Connector Reset & Speaker Connector Software Utilities Introduction Filename Purpose Assume that CD ROM drive is DInstallation of VGA Driver VGA Driver UtilityIntroduction Flash Bios UpdateInstallation of system Bios Page3-5 LAN Driver Utility Installation Procedure for Windows 9x/NT/2000/XP Sound Driver UtilityIntel Chipset Software Installation Utility Installation of Utility for Windows 2000/XPTouch Screen Driver Utility USB2.0 Software Installation UtilityInstallation of Utility for Windows 98SE/ 2000/XP Watchdog Timer Configuration Award Bios Setup Introduction Entering Setup Setup program initial screenStandard Cmos Features Cmos Setup screenIDE Primary Master / Slave IDE Secondary Master / Slave Video Halt onBase Memory Extended MemoryHard Disk Attributes Award Hard Disk Type TableCPU L1 & L2 Cache Advanced Bios FeaturesBios Features Setup Screen Quick Power on SELF-TEST FIRST/SECOND/BOOT DeviceBoot UP Floppy Seek Boot UP Numlock StatusSecurity Option Advanced Chipset Features Chipset Features Setup ScreenDram RAS# to CAS# Delay System Bios CacheableVideo Bios Cacheable Dram Timeing SelectablePCI SERR# NMI Integrated Peripherals Setup ScreenIntegrated Peripherals VIA Onchip IDE Device OnChip Primary PCI IDEPrimary Master/Slave PIO Secondary Master/Slave PIO Primary Master/Slave Udma Secondary Master/Slave UdmaOnboard Device Super IO Device Onboard Serial Port Power Management SetupPower Management Setup Screen Power Management Resume by AlarmAcpi Function SOFT-OFF by PWR-BTTNPNP/PCI Configuration PNP/PCI Configuration Setup ScreenReset Configuration Data Resource Controlled byIRQ Resources IRQ-n Assigned toPC Health Status Setup Screen Shutdown TemperatureCurrent CPU Temperature PC Health StatusFrequency Control Setup Screen Frequency ControlAuto Detect PCI CLK Spread SpectrumLoad FAIL-SAFE Defaults Load Optimized DefaultsTo Disable the Password Password SettingTo SET a Password Save & Exit Setup Exit Without Saving System Assembly Exploded Diagram for CF Card Hook Exploded Diagram for Fanless Back Cover Exploded Diagram for System Power Assembly Exploded Diagram for I/O Port Assembly Exploded Diagram for Motherboard Exploded Diagram for LCD Assembly Exploded Diagram for System Cable Exploded Diagram for System Inverter Board Exploded Diagram for Touch Panel Exploded Diagram for Front Panel Exploded Diagram for System I/O Side Exploded Diagram for Heatsink Exploded Diagram for Hard Disk Drive Exploded Diagram for Hard Disk Drive Holder Exploded Diagram for Power Holder Technical Summary Block Diagram Interrupt MAP IRQ AssignmentRTC Standard RAM Bank Code AssignmentDMA Channel Map Assignment Timer & DMA Channels MAPTimer Channel Map Assignment Memory MAP LPC SIOAddress Read Target Write Target Internal Unit FERR# /IGNNE#B-8