JVC DR-M7S manual Programme Recording, Select the L-2 Select mode, Recording mode, REC Mode

Filename [DR-M7EK_08Recording.fm]

	M7EK_01.book Page 65 Friday, April 2, 2004 11:21 AM	Masterpage:Right-No-Heading
DR-

65

Automatic Satellite

Programme

Recording

This function allows you to automatically record a satellite programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the unit’s L-2 IN/DECODER connector and programme the timer on the satellite receiver. When the signals come into the unit from the satellite receiver, the unit automatically turns on and starts recording.

	REC MODE
#	REC MODE
1 STANDBY/ON	PULL - OPEN
F1	DV DV IN
S-VIDEO VIDEO	L(MONO)-AUDIO-R

ATTENTION:

●Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the unit will start recording when the satellite receiver’s power is turned on.

●If you have connected another appliance other than a satellite receiver to the L-2 IN/DECODER connector, be sure not to engage the Automatic Satellite Programme Recording mode; otherwise, the unit will start recording when the connected appliance’s power is turned on.

●Automatic Satellite Programme Recording and timer-recording cannot be done at the same time.

Before performing the following steps:

●Make sure the satellite receiver is connected to the unit’s L-2 IN/DECODER connector. ( pg. 88)

●Programme the timer on the satellite receiver.

●Slide the TV/CABLE/SAT/DVD switch to TV.

A Select the L-2 SELECT mode.

Set “L-2 SELECT” to “SAT VIDEO” or “SAT S-VIDEO” ( pg. 83, “L-2 Select Setting (L-2 SELECT)”).

●Also refer to “IMPORTANT” on page 88.

B Set the recording speed.

Press REC MODE.

CANCEL	AUX MEMO/MARK
SHOW VIEW/ PROG/CHECK SAT#		TIMER
VIDEO Plus+
TOP MENU		NAVIGATION
	ENTER

SAT#	C	Engage the Automatic Satellite Programme
		Recording mode.

REC MODE

MENU		RETURN
PREVIOUS		NEXT
SLOW	PLAY/SELECT	SLOW
REC	STOP/CLEAR	PAUSE
REC MODE LIVE CHECK
SET UP		OPEN/
	DISPLAY ON SCREEN CLOSE

Press and hold SAT# for about 2 seconds. “SAT#” appears on the front display panel and the unit turns off automatically.

NOTES:

●To disengage the Automatic Satellite Programme Recording mode, press SAT#.

●If the unit’s power is off, it is not possible to engage the Automatic Satellite Programme Recording mode.

●In step C, if “SAT#” blinks quickly on the front display panel even though your satellite receiver’s power is off, Automatic Satellite

Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Manual Timer Programming” ( pg. 58) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Automatic Satellite Programme Recording is not possible with those satellite receivers.

●“SAT#” blinks on the front display panel while Automatic Satellite Programme Recording is in progress.

●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

●Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer.

●Pressing the unit’s 1 button while Automatic Satellite Programme Recording is in progress turns off the unit’s power and disengages the Automatic Satellite Programme Recording mode.

●If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Recording, it is not possible to set different recording speeds for each programme.

●Depending on the type of satellite receiver, the unit may not record a slight portion of the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Automatic Satellite Programme Recording mode when the satellite receiver’s power is on, the unit will not start Automatic Satellite Programme Recording even though “SAT#” blinks on the front display panel. When the satellite receiver shuts off once and is turned back on again, the unit starts recording.

●You can also record a programme from your cable system in the same way if the system has a timer.

●Just Clock ( pg. 102) does not work when the Automatic Satellite Programme Recording mode is engaged.

●When the Automatic Satellite Programme Recording mode is engaged, or the unit’s power is turned off after Automatic Satellite Programme Recording is finished, the unit will not enter the Timer mode even though “AUTO TIMER” is set to “ON” ( pg. 94).

Page 65

April 2, 2004 11:21 am