JVC DR-M7S manual Input Setting F-1 Input, Select the input mode for the L-2 Decoder connector

Filename [DR-M7EK_10Editing.fm]
DR-M7EK_01.book Page 83 Friday, April 2, 2004 11:21 AM	Masterpage:Right-No-Heading

83

L-2 Select Setting (L-2 SELECT)

Set “L-2 SELECT” to the appropriate mode depending on the type of appliance connected to the unit’s L-2 IN/DECODER connector.

Perform steps A and B of “L-1 Output and L-1 Input Setting (L-1 OUTPUT and L-1 INPUT)” on page 82.

A Select the input mode for the L-2 IN/

DECODER connector.

APress rt to move the

arrow to “L-2 SELECT”, then press ENTER.

B Press rt to select the appropriate setting, then press ENTER.

(The boldface settings in the table below indicate the settings at your purchase.)

8L-2 SELECT

Select “VIDEO” or “S-VIDEO” to use this unit as the recording deck with the player connected to the L-2 IN/ DECODER connector, or to use the satellite receiver connected to the L-2 IN/DECODER connector.

VIDEO: If a connected appliance’s output is compatible only with regular video signals, set to “VIDEO”.

S-VIDEO: If a connected appliance’s output is compatible with Y/C signals, set to “S-VIDEO”. You can obtain high- quality picture. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

Select “SAT VIDEO” or “SAT S-VIDEO” to view a satellite programme with the TV set while the unit is turned off. ( pg. 88)

SAT VIDEO: If a connected satellite receiver’s output is compatible only with regular video signals, set to “SAT VIDEO”.

SAT S-VIDEO: If a connected satellite receiver’s output is compatible with Y/C signals, set to “SAT S-VIDEO”. You can obtain a high-quality S-VHS picture. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

DECODER: To use a decoder connected to the L-2 IN/DECODER connector.

B Return to the normal screen.

Press SET UP.

NOTES:

●If you have a satellite receiver or a decoder connected to the L-2 IN/DECODER connector, be sure to set “L-2 SELECT” back to appropriate mode after editing.

●If you are not connecting a satellite receiver or a decoder to the L-2 IN/DECODER connector, leave “L-2 SELECT” set to “VIDEO”.

●When “L-2 SELECT” is set to “SAT VIDEO” and “SAT S-VIDEO”, “SAT” appears on the TV screen or front display panel instead of “L-2”.

●If “L-1 OUTPUT” is set to “SCART S-VIDEO”, it is not possible to set “L-2 SELECT” to “DECODER” or “SAT VIDEO”.

●If “L-1 OUTPUT” is set to “SCART RGB”, it is not possible to set “L-2 SELECT” to “DECODER” or “SAT S-VIDEO”.

●If “L-1 OUTPUT” is set to “COMPONENT” and “L-2 SELECT” to “SAT VIDEO”, “SAT S-VIDEO” or “DECODER”, be sure to connect the L-1 IN/OUT connector with a TV.

F-1 Input Setting (F-1 INPUT)

Set “F-1 INPUT” to the appropriate mode depending on the connector (VIDEO or S-VIDEO) being used on the front panel.

Perform steps A and B of “L-1 Output and L-1 Input Setting (L-1 OUTPUT and L-1 INPUT)” on page 82.

A Select the input mode for the VIDEO/

S-VIDEO connector.

APress rt to move the

arrow to “F-1 INPUT”, then press ENTER.

B Press rt to select the appropriate setting, then press ENTER.

(The boldface settings in the table below indicate the settings at your purchase.)

8F-1 INPUT

VIDEO: When connecting an appliance to the VIDEO input connector, set to “VIDEO”.

S-VIDEO: When connecting an appliance to the S-VIDEO input connector, set to “S-VIDEO”.

B Return to the normal screen.

Press SET UP.

Page 83

April 2, 2004 11:21 am