JVC HR-XV32E manual 78 EN, Timer Recording VHS deck

Page 78

Filename [XV3EX_11Trouble.fm]

 

XV3EX_01.book Page 78 Friday, August 22, 2003 12:21 PM

Masterpage:Left+

78 EN

TROUBLESHOOTING (cont.)

TIMER RECORDING (VHS deck)

OTHER PROBLEMS

Timer recording won’t work.

The clock and/or the timer have been set incorrectly. ]Re-perform the clock and/or timer settings.

The timer is not engaged.

]Press # and confirm that “#” is displayed on the front display panel.

Timer programming is not possible.

Timer recording is in progress.

]Timer programming can’t be performed while a timer recording is in progress. Wait until it finishes.

” on the front display panel won’t stop blinking.

The timer is engaged but there’s no cassette loaded. ]Load a cassette with the record safety tab intact.

”, “” and “” on the front display panel won’t stop blinking.

The loaded cassette has had its record safety tab removed. ]Remove the cassette and cover the hole with adhesive tape, or

insert a cassette with the record safety tab intact.

The end of the tape was reached during timer recording.

]The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

” blinks for 10 seconds and the Timer mode is disengaged.

# has been pressed when there are no programs in memory, or the timer record information has been programmed incorrectly.

]Check the programmed data and re-program as necessary, then press # again.

The SHOWVIEW system does not timer-record properly.

The unit’s channel positions have been set incorrectly.

]Refer to “SHOWVIEW® Timer Programming” ( pg. 24) and re- perform the procedure.

” and “” on the front display panel won’t stop blinking.

The end of the tape was reached during Instant Timer

Recording.

]The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

”, “” and “” on the front display panel won’t stop blinking.

The loaded cassette has had its record safety tab removed. ]Remove the cassette and cover the hole with adhesive tape, or

insert a cassette with the record safety tab intact.

The end of the tape was reached during Automatic Satellite Programme Recording.

]The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

The image of the TV broadcast appears distorted on the TV screen.

The unit is left turned on and the DVD deck is selected. ]Turn off the unit, or press VCR to select the VHS deck, then

press TV/VCR so that the VCR indicator disappears from the front display panel.

Whistling or howling is heard from the TV during camcorder recording.

The camcorder’s microphone is too close to the TV.

]Position the camcorder so its microphone is away from the TV.

The TV’s volume is too high. ]Turn the TV’s volume down.

When scanning channels, some of them are skipped over.

Those channels have been designated to be skipped.

]If you need the skipped channels, restore them. ( pg. 69)

The channel cannot be changed.

Recording is in progress.

]Press 9 to pause the recording, change channels, then press 4 to resume recording.

Channel settings that were made manually seem to have changed or disappeared.

After the manual settings were made, Auto Channel Set was

performed.

]Perform manual setting again.

No channels are stored in the unit’s memory.

The TV aerial cable was not connected to the unit when Auto Set Up was performed.

]Turn off the unit once and connect the TV aerial cable to the unit properly, then turn on the unit again. Then perform Auto Set Up again. ( pg. 10)

The fully-wired 21-pin SCART cable was not connected between the TV and the unit when Preset Download was performed.

]Turn off the unit once and connect the fully-wired 21-pin SCART cable to the unit properly, then turn on the unit again. Then perform Preset Download again. ( pg. 12)

ATTENTION

This unit contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the unit off and unplug the mains power cord. Then plug it in again and turn the unit on. Take out the cassette. After checking the cassette, operate the unit as usual.

Page 78

August 22, 2003 12:20 pm

Image 78
Contents HR-XV32E Use only discs marked with the following Safety PrecautionsFilename XV3EX03Safety.fm For ItalyContents Unplayable Discs About DiscsPlayable Discs Region NumberPlacing a Disc File Structure of DiscsCare and Handling of Discs Place the discFilename XV3EX06Index.fm Infrared Beam Receiving Window M Front Display Panel pgAugust 29, 2003 802 am Mode Display L-1, L-2, F-1 or SAT DVD Mode Indicator Tape Remaining Time Indicator  pgCassette Loaded Mark How To Use Situate the unit Check the contentsBasic Connections Connect the unit to TVTurn on the unit Auto Set Up10 EN Select your countryOn the front display panel Perform Auto Set UpConfirm/Set video channel On the on-screen display12 EN Preset DownloadPerform Preset Download Program Number SetResults of Auto Set Up/Preset PanelLink Functions DVD deck Select the mode setting14 EN Select the DVD deckLanguage Access the Country Set screenPress VCR so that the VCR indicator lights up Select the VHS deck16 EN Access the DVD Set Up menu screenSelect the mode DVD deck onlyLanguage Code List Start playback 18 ENFind the programme start point Stop playbackPlayback Features Instant ReView 20 ENManual Tracking Repeat PlaybackBasic Recording 22 EN Recording FeaturesInstant Timer Recording ITR Elapsed Recording Time IndicationPlayback S.T. Picture SystemReceiving Stereo and Bilingual Programmes RecordingHowv IEW Timer 24 ENProgramming VPS/PDC Recording Engage the unit’s timer modeVPS/PDC signal Satellite Receiver UsersExpress Timer 26 ENAccess the Programme Check screen To cancel or change a programmeDisengage the timer mode Cancel or change a programmeSelect the programme to modify Cancel or change programme setting28 EN Overlapping programmes blink on the TV screenBefore performing the following steps Select the L-2 Select modeRecording mode Set L-2 Select to A/V or SAT.  pgLoad the disc 30 ENBasic Playback Pause playbackAccess the PBC menu Locating a desired scene using the DVD menuAccess the DVD menu Locating the start point of the item or skip the itemResume Function 32 ENStill Picture/Frame-By-Frame Playback Variable Speed Search Memorize a resume pointAccess the selection menu Zooming 3D PhonicSelect the effect level VFP function Adjusting the picture quality 34 ENAccess the on-screen bar Basic operation on the on-screen barSelect the option Change the time information Select the repeat mode36 EN Select the menu itemTo cancel A-B Repeat Playback Access the repeat modeWhen using the Repeat button Select the end point38 EN Time SearchChapter Search To clear the programme table Press Play Setup Programme PlaybackSelect the tracks in the desired order Subtitle Selection Access the menu40 EN Random PlaybackSelect the view angle When using the Angle buttonAngle Selection Press AngleAudio Language Selection When using the A.MONITOR button42 EN Select the audio languageFor Video CD Audio Channel SelectionSelect the audio channel For Svcd44 EN Parental LockTo change the settings To temporarily release the Parental LockCountry/Area Code List for Parental Lock 46 ENXV3EX01.book Page 47 Friday, August 22, 2003 1221 PM About MP3 Disc What is MP3?48 EN MP3 control displaySelect the group Using the MP3 control displayMP3 Playback Press w e to select the desired groupTo start playback by specifying the group/track number 50 ENRepeat Playback Group/track selection To return to the MP3 control displayWhat is JPEG? Jpeg control displayPress rt to select the desired file, then press OK or Using the Jpeg control display52 EN Slide-show playback starts from the selected fileZooming Press Play Setup while the Jpeg Control screen is displayedRepeat Playback Group/file selection To return to the Jpeg control display54 EN Make connections Engage the Record Pause mode of the recording deckVideo Recorder Start the source player56 EN DubbingFrom DVD to VHS Prepare the audio device for dubbing Place a disc and load an MDPrepare the DVD deck for dubbing For the digital audio device58 EN Operate the TV Press 1 on the unit’s remote control to turn on the TVSet the TV brand code Keep pressing VCR down during step a60 EN ReceiverPerfect Connections Connect the decoder Select the input modeMake connections Set the tunerAccess the Mode Set screen Mode Set VHS deckAccess the Main Menu screen 62 ENWhen you use the Direct Rec function, be sure to use a TV For Example64 EN About Ntsc PlaybackPress rt to move H to RESUME, then press OK Mode Set DVD deckFor each mode setting, see pages 66 to Press rt to select ON, then press OK66 EN Picture SettingsAudio Settings MasterpageLeft+Digital Others SettingsPlayback discs Output Audio CD/Video CDAuto Channel Set 68 ENTuner Set Perform Auto Channel SetManual Channel Set 70 EN Delete a ChannelBroadcast Set Stations a Set Stations B72 EN TV Station And ID ListVideo Channel Set Access the Video Channel Set modeExit the Video Channel Set mode Set the RF output systemSet Just Clock 74 ENSet the date and time Set the source channel position for clock dataYou can disable the unit’s operation Child LockSet the Child Lock Playback VHS deck 76 ENTape Transport VHS deck Playback DVD deckRecording VHS deck MP3 Playback DVD deckJpeg Playback DVD deck Scene is not recorded from multiple anglesTimer Recording VHS deck 78 ENSignal system Signal-to-noise ratio 45 dBHorizontal resolution Memory backup time Approx min80 EN Time Search Timer Recording Top menu Tuner Set Country/Area Code ListSubtitle Selection Tape Position Indicator When programmes overlap each other82 EN Filename XV3EX12-2Memo.fmXV3EX01.book Page 83 Friday, August 22, 2003 1221 PM Filename XV32EX13Cov4.fm April 22, 2004 240 pm
Related manuals
Manual 84 pages 46.16 Kb