Operation with tape Playing a tape, Auto Tracking

Operation with tape

Playing a tape

You will only be able to load and eject video cassettes when your VCR is plugged into the mains.

Your VCR may also playback recordings from NTSC tapes (on PAL TV).

Getting a better picture

When a cassette is inserted and playback started, the automatic tracking function works to get the best possible picture automatically. If the quality of the recording is poor, repeatedly press 3 or 4 on the remote control to manually adjust the tracking until any distortions have been removed. Press numbered 0 on the remote control to switch automatic tracking back on again.

1VCR as described earlier in this book. Turn on your TV.

Press POWER to turn on your VCR. Insert the video cassette into your VCR.

The video cassette should have the window side facing up and the arrow facing away from you.Make sure that you have correctly connected your

2If you load a video cassette which has had its record protection tab removed, playback of the cassette will start automatically.

AUTO TRACKING

Your VCR will automatically adjust the tracking to give the best picture quality.

MANUAL TRACKING

If automatic tracking cannot eliminate noises well

during playback, adjust the tracking manually. Press and hold PR+ or - to eliminate the noises.Press PLAY 2 to start playing your tape.

Press				to still a picture.
3 Press				repeatedly to advance the tape frame by
3 Press				repeatedly to advance the tape frame by
frame.

If you hold down 6, the picture will be slowed down at about 1/19 times the normal playback.

Tapes can be paused for up to 5 minutes. After 5 minutes your VCR will stop the tape to prevent damaging the tape or your VCR .

Still picture quality can be improved slightly by pressing 3 or 4.

4Picture search:

During playing back press either 5 or 6 and this will enable you to rapidly wind the tape (7 times normal playback) and see where you are on the tape.

Logic search:

During fast forwarding or rewinding press and hold

5 or 6 the picture will be played back at 7 times normal playback speed.Press PLAY 2 to continue playing your tape.

Slow motion playback, Shuttle :

5 During playing back or still picture press F or G. You can reach the following playback speeds. (-7xplay, -3xplay, -play, still, 1/19 slow, play, 2xplay, 7xplay)

To switch off the slow motion and shuttle, press the desired function.

During slow motion and shuttle, the noise bars may appear on the picture according to the status of tape.

If distortions can be seen in the picture, reduce them with D or E.

6Press EJECT.

If the end of the tape is reached, your VCR will stop playback automatically, rewind, stop, eject the tape.Press 9 to end playback.

CM (Commercial Message) Skip:

This feature enables you during playback of a tape to skip a commercial break in a few seconds, then resume normal playback.

While tape is playing press			on the remote control to
skip commercial (or another programme material).
Repeatedly press		to skip:
1	Press 30 seconds
2	Press 60 seconds
3	Press 90 seconds
4	Press 120 seconds
5	Press 150 seconds
6	Press 180 seconds

EPC (Easy Picture Control)

This feature automatically improves playback picture quality by adjusting your VCR to the condition of the tape.

1Press MENU.

2Press 1 or 2 to select EPC.

3Press OK.

	OFF	Pr-12	1 2		A B
	PSET	ACMS	TIME	SYS-	C
RECSOFTR		ACMS	DATE	TEM	OSD
fOSDSHARPSTB + -					NIC	OPR
ON	16:9	THR-	DECO-	EPC		i
OFF	4:3	OUGH	DER	EPC

4SHARP.

Please note you may only set EPC when playing a tape.Press 3 or 4 repeatedly to select: OFF, SOFT or

5Press MENU return to screen.