JVC HR-XV2E owner manual Operation with tape, Press Showview, Video Programme System VPS

Page 24
ONCE
REC SHOWVIEW

Operation with tape

ShowView Programming

ShowView greatly simplifies entering the date, channel, start and end times of a Timer Recording by simply entering a ShowView Code. ShowView Codes are published in most TV guide magazines; they can vary one to nine numbers in length.

SHOWVIEW is a registered trademark of Gemstar Development Corporation.

The SHOWVIEW system is manufactured under licence from Gemstar Development Corporation.

1Make sure that TV channels have been tuned and stored in correct SHOWVIEW order.

Insert a video cassette with protection tab into your VCR.

2Press SHOWVIEW.

- - - - - - - - -

0~9, OK i

3Press D or E to select the recording type. ONCE: To record once.

WEEKLY: To record at the same time every week.

DAILY: To record every day (except Saturday and Sunday) at the same time.

4Press the numbered buttons to enter the ShowView Code of the TV programme that you wish to record.

If you make a mistake press F then enter the revised number.

 

246876543

 

ONCE

0~9,

OK i

REC SHOWVIEW

5Press OK.

If PLEASE CHECK is displayed it means that you have entered the wrong ShowView number, entered the ShowView number incorrectly.

If “- -” is displayed, you have to enter the pro- gramme number of the station, you want to record from.

PR

DATE

 

 

TIME

 

 

PR-01

12

10

: 11~11 : 55

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

i

6Press F or G to select the settings that you wish to revise. (PR, DATE, TIME, VPS and SP).

Press D or E to enter the correct information.

PR

DATE

 

 

TIME

 

 

 

PR-01

12

10

: 11~11 :

55

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

i

7Press G and press D or E to switch VPS/PDC on or off. Press G to select the recording speed. Press D or E to select the desired tape speed (SP, IP, or LP).

IP mode determines how much tape is left and switches speed from SP to LP, if necessary, to complete recording the program.

IP mode is not selected when VPS/PDC is ON. Check that the timer event details are correct.

If you wish to record from AUDIO IN and VIDEO IN on the front or from either of the EURO SCART sockets on the back of VCR, press AUX to select for correct display (AV1, AV2 or AV3).

PR

DATE

 

 

TIME

 

 

PR-01

12

10

: 11~11 : 55

 

SP

- -

- -

- -

:

- - - -~

- -:

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

- -

- -

- -

:

- - ~ - -

: - -

SP

i

8If you want to make another ShowView recording repeat stages 3 - 7 by pressing SHOWVIEW twice. Press MENU twice to return to TV Picture.

If PLEASE CHECK is displayed, you have entered incor- rect information and will need to re-enter the data.

Press POWER to switch your VCR power off mode.

will appear in the video recorder’s display while your VCR waits to make the recording. To watch a DVD during timer recording standby mode, press POWER and VCR/DVD to switch to DVD mode.

Note

Video Programme System (VPS)

The Video Programme System (VPS) ensures that the TV programmes that you have programmed for timer recording will be recorded exactly from their beginning to end, even if the actual broadcasting time differs from the scheduled time due to delayed start, or if the pro- gramme is extended beyond its scheduled time. Also, if a programme is interrupted, for example, if a news flash is inserted, the recording will also be interrupted auto- matically and resumed when the programme contin- ues.

The VPS signal is broadcast by the TV station and this controls the timer in the video recorder.

VPS should be set ON for all timer recordings from TV stations broadcasting these signals. It should be set OFF for all timer recordings from TV stations that are not broadcasting these signals.

***The similar system PDC, which is used in the time being in the Netherlands, can also be used with your new video recorder.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents HR-XV2E Important notes on controlling this unit For ItalyVCR Button Contents Before Use Playable DiscsDisc-related terms Types of video CDsPrecautions About SymbolsBefore Use Cont’d Power Front Panel and Display WindowDVD OPEN/CLOSE Play GRemote Control Remote Control Operation RangeRemote control battery installation Remote A/B/C/D Code Switching On the remote controlSet the remote control code On the unitTV Multi-Brand Remote Control Control Your TV Using Additional ButtonsBrand Name Code Rear Panel AerialCoaxial RF OUT DVD/VCR OUTConnections Basic connection AVBasic connection RF Component Video Color Stream connectionConnections Cont’d Connecting to Optional Equipment Digital Multi-channel soundCoaxial or Optical to the corresponding Initial preset Before Operation VCR partBefore Operation VCR part Setting the clock Manually Press Menu to remove the menus from the TV screenTo alter the HOURS, MINUTES, DAY, Month and Year Before Operation VCR part How to use the main menu Switch on your TV setPower button TV Station Table will appear when tuningBefore Operation VCR part Tuning in TV Stations Manually Press 2 to select MFT Press 3 or 4 to adjustHow to select Stored TV stations Before Operation VCR part Changing the order of TV StationsDeleting TV Stations ScreenBefore Operation DVD part General Explanation On-Screen DisplayOn-screen display operation Before Operation DVD part Initial Settings Initial Settings General OperationLanguage PictureBefore Operation DVD part SoundOthers Parental Control Rating DVDCountry Code DVD Changing the 4-digit codeOperation with tape Playing a tape Getting a better pictureAuto Tracking Manual TrackingOperation with tape Instant Timer Recording ITR Press Power to turn on your VCRMake sure that you have correctly connected your VCR as described earlier in this bookOperation with tape Press ShowviewVideo Programme System VPS Operation with tape Timer recording using On Screen Display If Timer record events OverlapExample General Features Operation with DVD and Video CD Playing a DVD and Video CDMoving to another Title Moving to another CHAPTER/TRACKOperation with DVD and Video CD General Features Still Picture and Frame-by-frame playbackTime Search DVD Video Discs Repeat Chapter/Title/OffSpecial DVD Features DVD Operation with Audio CD and MP3/WMA Disc About WMAWindow Media AudioInsert a disc and close the tray Press 3/4 to select the MP3 or WMA then pressOperation with Audio and MP3/WMA Disc Operation with Jpeg Disc Viewing a Jpeg disc Jpeg Moving to another FileRepeat All/Off Programmed Playback with Audio CD and MP3/WMA/JPEG Disc Programmed Playback with Video CDAdditional Operation VCR part On Screen Display Tape Counter Memory StopChild Lock Additional Operation VCR part Hi-Fi Stereo Sound System Wide Screen CompatibilityTo set the decoder Video Mode Setting DVD VCD2.0 VCD1.1 Additional Operation DVD partLast Condition Memory Screen SaverVCR will go into record mode Special Recording Copying from DVD To VCRRecording from another video recorder Stop the Copy ProcessTroubleshooting Symptom Cause CorrectionVideo Head Cleaning Language Code List Code LanguageCountry Code List Code CountrySpecification GeneralSystem HR-XV2E
Top Page Image Contents