JVC DR-MV5BE manual Manual Timer Programming, DVD Timer, For DVD deck

Filename [MV5S_08Basic TimerDub.fm]
MV5S_00.book Page 31 Wednesday, August 31, 2005 4:55 PM	Masterpage:Right+

TIMER RECORDING EN 31

	Manual Timer Programming	1 Press DVD or VHS to select the deck on which you want to
		perform timer programming.
		2 For DVD deck
		Load a recordable disc.
		For VHS deck
You can programme each deck to timer-record as many as		Load a cassette with safety tab intact.
8 programmes up to 30 days ahead.		3 Press PROG to access the
			VHS	DVD
If you do not know the SHOWVIEW number for the programme you		Programme Check screen.	DATE	START-STOP	TV PROG	DAILY/WEEKLY	VPS/PDC	REC MODE
wish to record, use the following procedure to set your unit to		4 For DVD deck	10/07 THU	22:00 - 22:30	10	WEEKLY	ON	XP
			05/07 SAT	19:00 - 20:00	44		ON	SP
timer-record the programme.			11/07 FRI	13:30 - 14:00	26		OFF	LP
		Press rt w e to select “DVD”	11/07 FRI	16:00 - 17:00	33		OFF	LP
			++++++++++++++++ NEW TIMER PROGRAMME				++++++++++++++++
		and press rt to select “NEW
● Make sure that the unit’s built-in clock is set properly.
		TIMER PROGRAMME”, then
● Turn on the unit.				DISC TIMER PRGM
		press ENTER.
● Turn on the TV and select the AV mode.			EXIT	OK	SELECT WITH [CURSORS]
		For VHS deck	PROG	SELECT	THEN PRESS [ENTER]
● Slide the TV/DVD switch to DVD.
		Press rt w e to select “VHS”	TIMER PROGRAMME
		and press rt to select “NEW
		TIMER PROGRAMME”, then	DATE	START		STOP	TV PROG
		press ENTER.	05/07 SAT 20:00		20:30		VTM 10

VHS

PROG ENTER

DVD

TIMER

5 Press rt to set the desired	DAILY/WEEKLY	VPS/PDC	NAME
			REC MODE
date.		OFF	LP
● The current date appears on the	EXIT	CONFIRM SET TIMER PROGRAMMING WITH [CURSORS]
TV screen. The date you enter	PROG	SELECT	THEN PRESS [ENTER]

appears in its place.

6 Press w e to select “START”, then press rt to set the desired start time.

●Each press of rt advances/goes back the start time in 1-min. increments.

●To advance/go back the start time in 30-min. increments, press and hold rt.

7 Press w e to select “STOP”, then press rt to set the desired stop time.

rtwe

Satellite Receiver Users (DVD Deck Only)

To timer-record a satellite broadcast using Manual Timer Programming:

APerform “Manual Timer Programming”.

BSet the satellite receiver to the appropriate channel before the selected programme begins.

C Select “L-2” in step 8.

D Leave the satellite receiver’s power on.

NOTES:

●Each press of rt advances/goes back the stop time in 1-min. increments.

●To advance/go back the stop time in 30-min. increments, press and hold rt.

8 Press w e to select “TV PROG”, then press rt to select the desired channel.

9 Press w e to select the desired recording option as required.

●Refer to step 6 in “SHOWVIEW™ Timer Programming” ( pg. 29).

10 Press ENTER to access the Programme Confirmation screen.

11 Press ENTER to complete timer programming.

●To programme another timer, repeat steps 3 – 11.

●If “PROGRAMME OVERLAPPED” appears on the TV screen, see page 35.

12 Press TIMER # to engage the unit’s timer mode. The DVD timer indicator lights up on the unit and the unit is automatically turned off.

●To disengage the timer mode, press TIMER # again.

●When two successive programmes are recorded on a DVD-RW disc with Manual Timer Programming function, the beginning of the second one may be left off the recording.

●If the copy limited programme is received during timer-recording, the unit enters Record Pause mode. Recording starts again if it is switched to a recordable broadcast during the time you programmed.

●In case of a power failure after programming, the unit’s memory backup keeps your selections for approximately 10 minutes.

●Programmes that start after midnight must have the next day’s date.

●To record the programmes received by the satellite receiver, record on the DVD discs. For details, refer to “Satellite Receiver Users (DVD Deck Only)” above.

Page 31Wednesday, 31 August 2005 16:55