JVC DR-MV5BE manual Tuner Set, Auto Channel Set, Vacant channels Press rt w e to select your

Filename [MV5S_13Subsidiary.fm]
MV5S_00.book Page 84 Wednesday, August 31, 2005 4:55 PM	Masterpage:Left+

84 EN SUBSIDIARY SETTINGS

Tuner Set	Auto Channel Set
	1 Press SET UP to access the Main Menu screen.
Your unit needs to memorise all necessary stations in channel
	2 Press w e to select “INITIAL SET UP”, then press t.
positions in order to record TV programmes. Auto Channel Set
automatically assigns all receivable stations in your area to call	3 Press w e to select “AUTO CH	DVD SET UP	FUNCTION SET UP INITIAL SET UP
them up by using the PR +/– buttons without going through any	SET”, then press t.	AUTO CH SET	MANUAL CH SET	GUIDE PR CLOCK SET
vacant channels.	4 Press rt w e to select your
● Turn on the unit.	country’s name, then press
	ENTER.
● Turn on the TV and select the AV mode.
	5 Press rt w e to select the
● Slide the TV/DVD switch to DVD.		SET UP	OK
	language of your choice.			SELECT WITH [CURSORS]
		EXIT	SELECT	THEN PRESS [ENTER]
	6 Press ENTER twice.
	● When you have connected the unit to a TV offering T-V Link via a
	fully-wired 21-pin SCART cable ( pg. 15), the unit automatically
	performs the Preset Download and the T-V LINK screen will appear.
	( pg. 18)
VHS	● The Auto Set screen appears, and remains on screen while the unit
	searches for receivable stations.
	Wait until the TV screen as shown in step 7 appears.
	7 View the Confirmation screen.
	“SCAN COMPLETED” is displayed on the TV screen. Press “OK”.

ENTER

SET UP

IMPORTANT:

Perform the following steps only if —

—Auto Channel Set has not been set correctly by Auto Set Up or by Preset Download. ( pg. 17, 18)

—you have moved to a different area or if a new station starts broadcasting in your area.

8 Press SET UP to complete the setting.

●When Auto Channel Set is completed, “PLEASE WAIT” will be displayed for about 90 seconds, since channel data is exchanged between the DVD deck and the VHS deck. No operations will be done during this time.

●Using the Confirmation screen, you can skip or add channel positions, enter station names and perform other operations. Refer to pages 85 – 87 for the procedures.

●Depending on reception conditions, the stations may not be stored in order, and the station names may not be stored correctly.

●For information on scrambled broadcasts, refer to “When Receiving A Scrambled Broadcast (DVD Deck Only)” ( pg. 87).

IMPORTANT:

●In certain reception conditions, station names may not be stored correctly, and Auto Guide Program Number Set may not work properly. When the Guide Program numbers are not set properly, the programme that you do not intended to record will be timer- recorded by the SHOWVIEW system of the unit. When programming the timer using the SHOWVIEW system, be sure to check the desired channel is selected correctly. ( pg. 29)

●Your unit memorises all receivable stations even if reception of some of them is poor. You can delete those stations with an unacceptable picture from the list. ( pg. 86, “Delete A Channel”)

NOTES:

●Fine tuning is performed automatically during Auto Channel Set. If you want to perform tuning manually, refer to “Fine-Tuning Channels Already Stored” ( pg. 87).

●If you perform Auto Channel Set when the aerial cable is not connected properly, “SCAN COMPLETED –NO SIGNAL–” appears on the TV screen in step 7. In such a case, make sure of the aerial connection and press ENTER; Auto Channel Set will start again.

●If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect. Select the appropriate TV system for those channels. ( pg. 87, “INFORMATION”)

Page 84Wednesday, 31 August 2005 16:55