Audiovox AXWD2002 owner manual Hookups, DVD/VCR to TV Connection, Switch, Connecting to a TV

HOOKUPS

DVD/VCR TO TV CONNECTION	SETTING THE CH3/CH4
	SWITCH

1.Disconnect the AC power cord of the TV from the AC outlet.

2.Disconnect the antenna or cable from the TV.

3.Connect the antenna or cable to the ANT-IN jack of the DVD/VCR.

4.Connect the DVD/VCR to the TV using the coaxial cable.

5.Plug the AC power cords of the DVD/VCR and TV into the AC outlets.

[VHF/UHF	[Indoor antenna]	[Back of the DVD/VCR]
combination antenna]			[Back of the
			UHF/VHF combination TV]
	OR	ANT - IN	Coaxial cable
			(supplied)
[Cable	box or satellite box] OR		UHF/VHF
		ANT - OUT
			CH3 CH4
From Cable or
Satellite Company

If your TV does not have A/V terminals:

When the DVD/VCR is in the VCR Playback mode or when the DVD/VCR is in the VCR mode, your TV will receive signals from the DVD/VCR on either channel 3 or channel 4. To use the DVD/VCR with your TV, set the selector switch to CH3 or CH4 (which is located in the back of your DVD/VCR), whichever is not used for normal broadcasts in your area. Then set your TV to the same channel.

ANT - IN

CH3 CH4 - OUT

CH3 CH4

[Back of the DVD/VCR]

Note to CATV system installer

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that pro- vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the building, as close to the point of cable entry as practical.

CONNECTING TO A TV

			DVD/VCR	COMPONENT
			OUT
Antenna/Cable signal			IN	VIDEO OUT
		ANT - IN	L	DVD/VCR	Y
			AUDO	AUDIO OUT
					Cb S-VIDEO	DIGITAL AUDIO OUT
A/V-compatible or			R	L
					OUT	PCM / BITSTREAM
		ANT - OUT				COAXIAL
wide screen TV		CH3 CH4	VIDEO	R	Cr
	To ANT. IN
	of TV
	To VIDEO INPUT jack		To VIDEO OUT jack			[Fig. 1]
	To Right (red) and Left (white)
	To AUDIO INPUT jacks		To AUDIO OUT jacks

Notes

¡Connect the DVD/VCR directly to a TV. If the A/V cables are connected to a VCR, pictures may be distorted due to the copy protection system.

CONNECTING TO A TV THAT HAS AN

S-VIDEO INPUT JACK OR COMPONENT VIDEO IN JACKS

FOR TVs WITH S-VIDEO INPUT JACK

Use an S-Video cable (commercially available) in place of the yellow video cable to enjoy higher quality pic- tures.

The S-Video connection only supplies video (picture) in the DVD mode of the DVD/VCR. Therefore, in order to use the VCR features or view TV channels on the DVD/VCR, you still need to either connect the RF coaxial cable between the ANT-OUT jack of the DVD/VCR and the TV’s Antenna In jack, or connect the yellow video cable as described earlier (Fig.1). To connect the supplied RF coaxial cable, see “DVD/VCR TO TV CONNECTION” above.

		DVD/VCR		COMPONENT
		OUT
		IN		VIDEO OUT
	ANT - IN	L		Y
			DVD/VCR
		AUDO	AUDIO OUT
A/V-compatible or					DIGITAL AUDIO OUT
		R	L	Cb S-VIDEO
				OUT PCM / BITSTREAM
wide screen TV	ANT - OUT				COAXIAL
	CH3 CH4	VIDEO	R	Cr
	To Right (red) and Left (white)
	To AUDIO INPUT jacks	To AUDIO OUT jacks			[Fig. 2]
	To S-VIDEO INPUT jack	To S-VIDEO OUT jack
		– 14 –			EN

1L25